SIP J. Rosenberg Internet-Draft Cisco Intended status: Standards Track March 5, 2007 Expires: September 6, 2007 Obtaining and Using Globally Routable User Agent (UA) URIs (GRUU) in the Session Initiation Protocol (SIP) draft-ietf-sip-gruu-12 Status of this Memo By submitting this Internet-Draft, each author represents that any applicable patent or other IPR claims of which he or she is aware have been or will be disclosed, and any of which he or she becomes aware will be disclosed, in accordance with Section 6 of BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. This Internet-Draft will expire on September 6, 2007. Copyright Notice Copyright (C) The IETF Trust (2007). Abstract Several applications of the Session Initiation Protocol (SIP) require a user agent (UA) to construct and distribute a URI that can be used by anyone on the Internet to route a call to that specific UA instance. A URI that routes to a specific UA instance is called a Globally Routable UA URI (GRUU). This document describes an extension to SIP for obtaining a GRUU from a registrar and for communicating a GRUU to a peer within a dialog. Rosenberg Expires September 6, 2007 [Page 1] Internet-Draft GRUU Mechanism March 2007 Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 5 3. Overview of Operation . . . . . . . . . . . . . . . . . . . . 5 3.1. Structure of GRUUs . . . . . . . . . . . . . . . . . . . . 5 3.1.1. GRUUs Which Expose the Underlying AOR . . . . . . . . 6 3.1.2. GRUUs Which Hide the Underlying AOR . . . . . . . . . 6 3.2. Obtaining a GRUU . . . . . . . . . . . . . . . . . . . . . 7 3.3. Using a GRUU . . . . . . . . . . . . . . . . . . . . . . . 8 3.4. Dereferencing a GRUU . . . . . . . . . . . . . . . . . . . 8 4. User Agent Behavior . . . . . . . . . . . . . . . . . . . . . 8 4.1. Generating a REGISTER Request . . . . . . . . . . . . . . 8 4.2. Learning GRUUs from REGISTER Responses . . . . . . . . . . 9 4.3. Constructing a Self-Made GRUU . . . . . . . . . . . . . . 10 4.4. Using Ones Own GRUUs . . . . . . . . . . . . . . . . . . . 11 4.4.1. Considerations for Multiple AORs . . . . . . . . . . . 11 4.5. Dereferencing a GRUU . . . . . . . . . . . . . . . . . . . 12 4.6. Rendering GRUUs on a User Interface . . . . . . . . . . . 13 5. Registrar Behavior . . . . . . . . . . . . . . . . . . . . . . 13 5.1. Processing a REGISTER Request . . . . . . . . . . . . . . 13 5.2. Generating a REGISTER Response . . . . . . . . . . . . . . 14 5.3. Timing Out a Registration . . . . . . . . . . . . . . . . 15 5.4. Creation of a GRUU . . . . . . . . . . . . . . . . . . . . 15 5.5. Registration Event Support . . . . . . . . . . . . . . . . 17 6. Proxy Behavior . . . . . . . . . . . . . . . . . . . . . . . . 17 6.1. Request Targeting . . . . . . . . . . . . . . . . . . . . 18 6.2. Record-Routing . . . . . . . . . . . . . . . . . . . . . . 19 7. Grammar . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 8. Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 20 9. Example Call Flow . . . . . . . . . . . . . . . . . . . . . . 22 10. Security Considerations . . . . . . . . . . . . . . . . . . . 26 10.1. Outside Attacks . . . . . . . . . . . . . . . . . . . . . 27 10.2. Inside Attacks . . . . . . . . . . . . . . . . . . . . . . 27 10.3. Privacy Considerations . . . . . . . . . . . . . . . . . . 28 11. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 30 11.1. Header Field Parameter . . . . . . . . . . . . . . . . . . 30 11.2. URI Parameter . . . . . . . . . . . . . . . . . . . . . . 30 11.3. SIP Option Tag . . . . . . . . . . . . . . . . . . . . . . 30 12. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 31 13. References . . . . . . . . . . . . . . . . . . . . . . . . . . 31 13.1. Normative References . . . . . . . . . . . . . . . . . . . 31 13.2. Informative References . . . . . . . . . . . . . . . . . . 32 Appendix A. Example GRUU Construction Algorithms . . . . . . . . 33 A.1. Public GRUU Algorithm . . . . . . . . . . . . . . . . . . 33 A.2. Temporary GRUU . . . . . . . . . . . . . . . . . . . . . . 33 Appendix B. Network Design Considerations . . . . . . . . . . . . 35 Author's Address . . . . . . . . . . . . . . . . . . . . . . . . . 36 Rosenberg Expires September 6, 2007 [Page 2] Internet-Draft GRUU Mechanism March 2007 Intellectual Property and Copyright Statements . . . . . . . . . . 37 Rosenberg Expires September 6, 2007 [Page 3] Internet-Draft GRUU Mechanism March 2007 1. Introduction In the Session Initiation Protocol (SIP), RFC 3261 [1], the basic unit of reference is the Address-Of-Record (AOR). However, in SIP systems a single user can have a number of user agents (handsets, softphones, voicemail accounts, etc.) which are all referenced by the same AOR. There are a number of contexts in which it is desirable to have an identifier which addresses a single user agent rather than the group of user agents indicated by an AOR. As an example, consider a blind transfer application [18]. User A is talking to user B. User A wants to transfer the call to user C. So, user A sends a REFER to user C. That REFER looks like, in part: REFER sip:C@example.com SIP/2.0 From: sip:A@example.com;tag=99asd To: sip:C@example.com Refer-To: (URI that identifies B's UA) The Refer-To header field needs to contain a URI that can be used by user C to place a call to user B. However, this call needs to route to the specific UA instance that user B is using to talk to user A. If it doesn't, the transfer service will not execute properly. For example, if A provides C with B's AOR, the call might be routed to B's voice mail rather than B's current handset. In order to enable this functionality, User B provides an instance- specific URI to User A in the Contact header of their SIP exchange. This URI refers only the the user agent B is currently using and can be provided to user C. Because user B doesn't know in advance who user A will transfer the call to, the URI has to be usable by anyone. Many current clients attempt to meet the need for an instance- specific identifier by using explicit IP addresses in the values they provide in the Contact header field. However, this interacts poorly with NATs and firewalls, and as a practical matter these URIs cannot be used by arbitrary external clients. Similarly, usage of hostnames has proven problematic for similar reasons. In addition, many SIP clients do not have or cannot obtain a hostname for themselves at all. This specification describes a mechanism for providing a unique user- agent identifier which is still globally routable. This identifier is called a Globally Routable User Agent (UA) URI (GRUU). Rosenberg Expires September 6, 2007 [Page 4] Internet-Draft GRUU Mechanism March 2007 2. Terminology The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [4]. This specification defines the following additional terms: contact: The term "contact", when used in all lowercase, refers to a URI that is bound to an AOR and GRUU by means of a registration. A contact is usually a SIP URI, and is bound to the AOR and GRUU through a REGISTER request by appearing as a value of the Contact header field. The contact URI identifies a specific UA. remote target: The term "remote target" refers to a URI that a user agent uses to identify itself for receipt of both mid-dialog and out-of-dialog requests. A remote target is established by placing a URI in the Contact header field of a dialog-forming request or response and updated by target refresh requests or responses. Contact header field: The term "Contact header field", with a capitalized C, refers to the header field which can appear in REGISTER requests and responses, redirects, or in dialog-creating requests and responses. Depending on the semantics, the Contact header field sometimes conveys a contact, and sometimes conveys a remote target. 3. Overview of Operation The basic idea behind a GRUU is simple. GRUUs are issued by SIP domains and always route back to a proxy in that domain. The domain in turn maintains the binding between the GRUU and the particular UA instance. When a GRUU is de-referenced when sending a SIP request, that request arrives at the proxy. It maps the GRUU to the contact for the particular UA instance, and sends the request there. 3.1. Structure of GRUUs A GRUU is a SIP URI that has two properties: o It routes to a specific UA instance. o It can be successfully de-referenced by any user agent on the Internet, not just ones in the same domain or IP network as the UA instance to which the GRUU points. In principle, a GRUU can be constructed in any way the domain Rosenberg Expires September 6, 2007 [Page 5] Internet-Draft GRUU Mechanism March 2007 chooses, as long as it meets the criteria above. However, all GRUUs contain the "gr" URI parameter (either with or without a value), so that a recipient of a GRUU can tell that it has these two properties. In practice, there are two different types of GRUUs: 1. GRUUs which expose the underlying AOR 2. GRUUs which hide the underlying AOR 3.1.1. GRUUs Which Expose the Underlying AOR In many cases it is desirable to construct the GRUU in such a way that the mapping to the AOR is apparent. For example, many user agents retain call logs, which keep track of incoming and outgoing call attempts. If the UA had made a call towards a GRUU (perhaps as a consequence of a transfer request), the call log will contain the GRUU. Since the call log is rendered to the user, it would be useful to be able to present the user with the AOR instead, since the AOR is meaningful to users as an identifier. This type of GRUU is called a public GRUU. It is constructed by taking the AOR, and adding the "gr" URI parameter with a value chosen by the registrar in the domain. The value of the "gr" parameter contains a representation of the UA instance. For instance, if the AOR was "sip:alice@example.com", the GRUU might be: sip:alice@example.com;gr=kjh29x97us97d If a UA removes the "gr" parameter, the result is the AOR. Since many systems ignore unknown parameters anyway, a public GRUU will "look" like the AOR to those systems. 3.1.2. GRUUs Which Hide the Underlying AOR In other cases it is desirable to construct a GRUU that obfuscates the AOR such that it cannot be extracted by a recipient of the GRUU. Such a GRUU is called a temporary GRUU. The most obvious reason to do this is to protect the user's privacy. In such cases, the GRUU may have any content provided that it meets the requirements in Section 3.1, and the AOR cannot be readily determined from the GRUU. The GRUU will have the "gr" parameter, either with or without a value. In order to avoid creating excessive state in the registrar, it is often desirable to construct cryptographically protected "stateless" GRUUs using an algorithm like that described in Appendix A. Rosenberg Expires September 6, 2007 [Page 6] Internet-Draft GRUU Mechanism March 2007 3.2. Obtaining a GRUU A User Agent can obtain a GRUU in one of several ways: o As part of its REGISTER transaction. o By constructing one locally, using the IP address or hostname of the user agent instance as the domain part of the URI. These are called self-made GRUUs, and are only really GRUUs when constructed by UA that know they are globally reachable using their IP address or hostname. o Via some locally-specified Administrative mechanism. A UA which wants to obtain a GRUU via its REGISTER request does so by providing an instance ID in the "+sip.instance" parameter in the Contact header field [12]. For example: Contact: ;+sip.instance="" The registrar detects this parameter and provides two GRUUs in the REGISTER response. One of these is a temporary GRUU, and the other is the public GRUU. These two GRUUs are returned in the "temp-gruu" and "pub-gruu" parameters, respectively, in the Contact header field of the response. For example: Contact: ;pub-gruu="sip:callee@example.com;gr=urn: uuid:f81d4fae-7dec-11d0-a765-00a0c91e6bf6" ;temp-gruu="sip:8ffkas08af7fasklzi9@example.com;gr" ;+sip.instance="" ;expires=3600 When a user agent refreshes this registration prior to its expiration, the registrar will return back the same public GRUU, but will create a new temporary GRUU. Despite the fact that each refresh provides the UA with a new temporary GRUU, all of the temporary GRUUs learned from previous REGISTER responses during the lifetime of a contact remain valid as long as (1) that contact remains registered, and (2) the UA doesn't change the Call-ID in its REGISTER request compared to previous ones. When the contact expires, either through explicit de-registration or timeout, all of the temporary GRUUs be invalidated. Similarly, if a register refresh changes the Call-ID compared to previous register refreshes, all of the previous temporary GRUUs are invalidated. When the user agent later creates a Rosenberg Expires September 6, 2007 [Page 7] Internet-Draft GRUU Mechanism March 2007 new registration with the same instance ID, the public GRUU is the same. The temporary GRUU will be new (as it is with refreshes), and it will be the only valid temporary GRUU for the instance until the next refresh, at which point a second one becomes valid too. Consequently, temporary GRUUs "accumulate" during the lifetime of a registration. 3.3. Using a GRUU Once a user agent obtains GRUUs from the registrar, it uses them in several ways. Firstly, it uses them as the contents of the Contact header field in non-REGISTER requests and responses that it emits (for example, an INVITE request and 200 OK response). According to RFC 3261, the Contact header field is supposed to contain a URI that routes to that user agent. Prior to this specification, there hasn't been a way to really meet that requirement. The user agent would use one of its temporary GRUUs for anonymous calls, and use its public GRUU otherwise. In addition, the UA can use the GRUU in any other place it needs to use a URI that resolves to itself, such as a webpage. 3.4. Dereferencing a GRUU Because a GRUU is simply a URI, a UA dereferences it in exactly the same way as it would any other URI. However, once the request has been routed to the appropriate proxy, the behavior is slightly different. The proxy will map the GRUU to the AOR and determine the set of contacts that the particular UA instance has registered. The GRUU is then mapped to those contacts, and the request is routed towards the UA. 4. User Agent Behavior This section defines the normative behavior for user agents. 4.1. Generating a REGISTER Request When a UA compliant to this specification generates a REGISTER request (initial or refresh), it MUST include the Supported header field in the request. The value of that header field MUST include "gruu" as one of the option tags. This alerts the registrar for the domain that the UA supports the GRUU mechanism. Furthermore, for each contact for which the UA desires to obtain a GRUU, the UA MUST include a "sip.instance" media feature tag [12] as a UA characteristic [7], whose value MUST be the instance ID that Rosenberg Expires September 6, 2007 [Page 8] Internet-Draft GRUU Mechanism March 2007 identifies the UA instance being registered. Each such Contact header field SHOULD NOT contain a "pub-gruu" or "temp-gruu" header field. The contact URI MUST NOT be equivalent, based on the URI equality rules in RFC 3261, to the AOR in the To header field. If the contact URI is a GRUU, it MUST NOT be a GRUU for the AOR in the To header field. As in RFC 3261, the Call-ID in a REGISTER refresh SHOULD be identical to the Call-ID used to previously register a contact. With GRUU, an additional consideration applies. If the Call-ID changes in a register refresh, the server will invalidate all temp-gruu associated with that UA instance; the only valid one will be the new one returned in that REGISTER response. Consequently, if a UA wishes its previously obtained temporary GRUUs to remain valid, it MUST utilize the same Call-ID in REGISTER refreshes. However, it MAY change the Call-ID in a refresh if invalidation is the desired objective. Note that, if any dialogs are in progress that utilize a temporary GRUU as a remote target, and a UA performs a registration refresh with a change in Call-ID, those temporary GRUU become invalid, and the UA will not be reachable for subsequent mid-dialog messages. If a UA instance is trying to register multiple contacts for the same instance for the purposes of redundancy, it MUST use the procedures defined in [12]. A UA utilizing GRUUs can still perform third party registrations and can include contacts which omit the "+sip.instance" Contact header field parameter. If a UA wishes to guarantee that the REGISTER request is not processed unless the domain supports and uses this extension, it MAY include a Require header field in the request with a value that contains the "gruu" option tag. This is in addition to the presence of the Supported header field also containing the "gruu" option tag. The use of Proxy-Require is not necessary and is NOT RECOMMENDED. 4.2. Learning GRUUs from REGISTER Responses If the REGISTER response is a 2xx, each Contact header field that contains the "+sip.instance" Contact header field parameter may also contain a "pub-gruu" and "temp-gruu" Contact header field parameter. These parameters convey the public and a temporary GRUU for the UA instance, respectively. A UA MUST be prepared for a Contact header field to contain just a "pub-gruu", just a "temp-gruu", neither, or both. The temporary GRUU will be valid for the duration of the registration, while the public GRUU persists across registrations. The UA will receive a new temporary GRUU in each successful REGISTER response, while the public GRUU will typically be the same. However, Rosenberg Expires September 6, 2007 [Page 9] Internet-Draft GRUU Mechanism March 2007 a UA MUST be prepared for the public GRUU to change from a previous one, since the persistence property is not guaranteed with complete certainty. If a UA changed its Call-ID in this REGISTER request compared to a previous REGISTER request for the same contact, the UA MUST discard all temporary GRUU learned through prior REGISTER responses. A UA MAY retain zero, one, some, or all of the temporary GRUUs that it is provided during the time over which its contact remains registered. If a UA stores any temporary GRUUs for use during its registration, it needs to be certain that the registration does not accidentally lapse due to clock skew between the UA and registrar. Consequently, the UA MUST refresh its registration well in advance of expiration. In cases where registrars forcefully shorten registration intervals, the registration event package, RFC 3860 [23] is used by user agents to learn of these changes. A user agent implementing both RFC 3680 and GRUU MUST also implement the extensions to RFC 3680 for conveying information on GRUU [24], as these are necessary to keep the set of temporary GRUU synchronized between the UA and the registrar. A non-2xx response to the REGISTER request has no impact on any existing GRUUs previously provided to the UA. Specifically, if a previously successful REGISTER request provided the UA with a GRUU, a subsequent failed request does not remove, delete, or otherwise invalidate the GRUU. The GRUU learned by the UA in the REGISTER response MUST be treated opaquely by the UA. That is, the UA MUST NOT modify it in any way (including adding or removal of URI parameters). 4.3. Constructing a Self-Made GRUU Many user agents, such as gateways to the Public Switched Telephone Network (PSTN), conferencing servers and media servers, do not perform registrations, and cannot obtain GRUUs through that mechanism. These types of user agents may be publicly reachable. This would mean that the policy of the domain is that requests can come from anywhere on the public Internet and be delivered to the user agent without requiring processing by intervening proxies within the domain. Furthermore, firewall and NAT policies administered by the domain would allow such requests into the network. When a user agent is certain that these conditions are met, a UA MAY construct a self-made GRUU. Of course, a user agent which does REGISTER, but for whom these conditions are met regardless, MAY also construct a self- made GRUU. However, usage of GRUUs obtained by the registrar is RECOMMENDED instead. A self-made GRUU is one whose domain part equals the IP address or hostname of the user agent. The user part of the SIP URI is chosen Rosenberg Expires September 6, 2007 [Page 10] Internet-Draft GRUU Mechanism March 2007 arbitrarily by the user agent. Like all other GRUUs, the URI MUST contain the "gr" URI parameter, with or without a value, indicating it is a GRUU. If a user agent does not register, but it is not publicly reachable, it would need to obtain a GRUU through some other means. Typically, the UA would be configured with a GRUU, and the GRUU would also be configured into the proxy which will receive requests targeted to the GRUU, along with a static mapping to the IP address and port of the UA. 4.4. Using Ones Own GRUUs A UA SHOULD use a GRUU when populating the Contact header field of dialog-forming and target refresh requests and responses. In other words, a UA compliant to this specification SHOULD use one of its GRUUs as its remote target. This includes the INVITE request, its 2xx response or 18x response with a To tag, the SUBSCRIBE [5] request, its 2xx response or with a To tag, the NOTIFY request, the REFER [6] request, its 2xx response, and the UPDATE request and its 2xx response. The only reason not to use a GRUU would be privacy considerations; see Section 10.3. When using a GRUU obtained through registrations, a UA MUST have an active registration prior to using a GRUU, and MUST use a GRUU learned through that registration. It MUST NOT reuse a GRUU learned through a previous registration which has lapsed (in other words, one obtained when registering a contact which has expired). The UA MAY use either the public or one of its temporary GRUUs provided by its registrar. A UA MUST NOT use a temporary GRUU learned in a REGISTER response whose Call-ID differs from the one in the most recent REGISTER request generated by the UA for the same AOR and instance ID. Of course, when a UA wishes to construct an anonymous request as described in RFC 3323 [13], it SHOULD use a temporary GRUU. See Section 10.3 for a more complete discussion on the level of privacy afforded by temporary GRUUs. As per RFC 3261, a UA SHOULD include a Supported header with the option tag "gruu" in requests and responses it generates. 4.4.1. Considerations for Multiple AORs In some SIP networks, a user agent may have a multiplicity of AOR, either in different domains, or within the same domain. In such cases, additional considerations apply. When a UA sends a request, the request will be sent 'using' one of its AOR. This AOR will typically show up in the From header field of Rosenberg Expires September 6, 2007 [Page 11] Internet-Draft GRUU Mechanism March 2007 the request, and credentials unique to that AOR will be used to authenticate the request. The GRUU placed into the Contact header field of such a request SHOULD be one that is associated with the AOR used to send the request. In cases where the UA uses a tel URI [11] to populate the From header field, the UA typically has a SIP AOR that is treated as an alias for the tel URI. The GRUU associated with that SIP AOR SHOULD be used in the Contact header field. When a UA receives a request, the GRUU placed into the Contact header field of a 2xx response SHOULD be the one associated with the AOR or GRUU to which the request was most recently targeted. There are several ways to determine the AOR or GRUU to which a request was sent. For example, if a UA registered a different contact to each AOR (by using a different user part of the URI), the Request-URI (which contains that contact) will indicate the AOR. 4.5. Dereferencing a GRUU A GRUU is identified by the presence of the "gr" URI parameter, and this parameter may or may not have a value. A UA that wishes to send a request to a URI that contains a GRUU knows that the request will be delivered to a specific UA instance without further action on the part of the requestor. Some UAs implement non-standard mechanisms for handling URIs that compensate for the fact that heretofore many contact URIs have not been globally routable. Since any URI containing the "gr" parameter is known to be globally routable, a UA SHOULD NOT apply such mechanisms when contact URI contain the "gr" parameter. Because the instance ID is a callee capabilities parameter, a UA might be tempted to send a request to the AOR of a user, and include an Accept-Contact header field [16] that indicates a preference for routing the request to a UA with a specific instance ID. Although this would appear to have the same effect as sending a request to the GRUU, it does not. The caller preferences expressed in the Accept-Contact header field are just preferences. Its efficacy depends on a UA constructing an Accept- Contact header field that interacts with domain-processing logic for an AOR, to cause a request to route to a particular instance. Given the variability in routing logic in a domain (for example, time-based routing to only selected contacts), this doesn't work for many domain-routing policies. However, this specification does not forbid a client from attempting such a request, as there may be cases where the desired operation truly is a preferential routing request. Rosenberg Expires September 6, 2007 [Page 12] Internet-Draft GRUU Mechanism March 2007 4.6. Rendering GRUUs on a User Interface When rendering a GRUU to a user through a user interface, it is RECOMMENDED that the "gr" parameter be removed. For public GRUUs, this will produce the AOR, as desired. For temporary GRUUs, the resulting URI will be seemingly random. Future work may provide improved mechanisms that would allow an automata to know that a URI is anonymized and thus should not be rendered. 5. Registrar Behavior 5.1. Processing a REGISTER Request A REGISTER request might contain a Require header field with the "gruu" option tag; this indicates that the registrar has to understand this extension in order to process the request. It does not require the registrar to create GRUUs, however. As the registrar is processing the contacts in the REGISTER request according to the procedures of step 7 in Section 10.3 of RFC 3261, the registrar checks whether each Contact header field in the REGISTER message contains a "+sip.instance" header field parameter. If present, the contact is processed further based on the rules in the remainder of this section. Otherwise, the contact is processed based on normal RFC 3261 rules. If the contact URI is equivalent (based on URI equivalence in RFC 3261) to the AOR, the registrar MUST reject the request with a 403, since this would cause a routing loop. If the contact URI is a GRUU for the AOR in the To header field of the REGISTER request, the registrar MUST reject the request with a 403, for the same reason. If the contact is not a SIP URI, the REGISTER request MUST be rejected with a 403. Next, the registrar checks if there is already a valid public GRUU for the AOR (present in the To header field of the REGISTER request) and the instance ID (present as the content of the "+sip.instance" Contact header field parameter). If there is no valid public GRUU, the registrar SHOULD construct a public GRUU at this time according to the procedures of Section 5.4. The public GRUU MUST be constructed by adding the "gr" URI parameter, with a value, to the AOR. If the contact contained a "pub-gruu" Contact header field parameter, the parameter MUST be ignored by the registrar. A UA cannot suggest or otherwise provide a public GRUU to the registrar. Next, the registrar checks for any existing contacts registered to the AOR and instance ID. If there is at least one, the registrar Rosenberg Expires September 6, 2007 [Page 13] Internet-Draft GRUU Mechanism March 2007 finds the one that was most recently registered, and examines the Call-ID value associated with that registered contact. If it differs from the one in the REGISTER request, the registrar MUST invalidate all previously generated temporary GRUU for the AOR and instance ID. A consequence of this invalidation is that requests addressed to those GRUU will be rejected by the domain with a 404 from this point forward. Next, the registrar SHOULD create a new temporary GRUU for the AOR and instance ID with the characteristics described in Section 5.4. The temporary GRUU construction algorithm MUST have the following two properties: 1. The likelihood that the temporary GRUU is equal to another GRUU which the registrar has created MUST be vanishingly small. 2. Given a pair of GRUUs, it MUST be computationally infeasible to determine whether they were issued for the same AOR or instance ID or different AORs and instance IDs. If the contact contained a "temp-gruu" Contact header field parameter, the parameter MUST be ignored by the registrar. A UA cannot suggest or otherwise provide a temporary GRUU to the registrar. 5.2. Generating a REGISTER Response When generating the 200 (OK) response to the REGISTER request, the procedures of step 8 of Section 10.3 of RFC 3261 are followed. Furthermore, for each Contact header field value placed in the response, if the registrar has stored an instance ID associated with that contact, that instance ID is returned as a Contact header field parameter. If the REGISTER request contained a Supported header field that included the "gruu" option tag, and the registrar has at least one temporary GRUU assigned to the instance ID and AOR, the registrar MUST add an "temp-gruu" Contact header field parameter to that Contact header field. The value of the "temp-gruu" parameter is a quoted string, and MUST contain the mostly recently created temporary GRUU for that AOR and instance ID. In addition, if the registrar has a public GRUU assigned to the instance ID and AOR (and the client supports GRUUs), the registrar MUST add a "pub-gruu" Contact header field parameter to that Contact header field. The value of the "pub-gruu" parameter is the public GRUU. Note that handling of a REGISTER request containing a Contact header field with value "*" and an expiration of 0 still retains the meaning defined in RFC 3261 -- all contacts, not just those with a specific instance ID, are deleted. As described in Rosenberg Expires September 6, 2007 [Page 14] Internet-Draft GRUU Mechanism March 2007 Section 5.4, this removes the binding of each contact to the AOR and the binding of each contact to its GRUUs. The registrar SHOULD NOT include the "gruu" option tag in the Require or Supported header field of the response. 5.3. Timing Out a Registration When a registered contact expires (either due to timeout or explicit de-registration), its binding to the AOR is removed as usual. In addition, its binding to its GRUUs are removed at the same time as a consequence of the relationships described in Section 5.4 If, as a consequence of the expiration of the contact, a particular GRUU no longer has any registered contacts bound to it, and the GRUU is a temporary GRUU, the GRUU MUST be invalidated. This means that all of the accumulated temporary GRUUs get invalidated once the last contact for a given instance ID expires. If, however, the GRUU was a public GRUU, the registrar SHOULD continue to treat the GRUU as valid. Consequently, subsequent requests targeted to the GRUU, prior to re-registration of a contact to the GRUU, SHOULD return a 480. In addition, since the GRUU remains valid, the rules in Section 5.1 will cause it to be retained when a contact with that instance ID is once again registered to the AOR. These rules give a public GRUU a semi-permanent property. The intent is that the registrar make every attempt to retain validity of the GRUU for as long as the AOR itself is known within the domain. The requirements for doing so are at SHOULD strength and not MUST strength because of the difficulty in meeting a MUST strength requirement; registrar failures could cause the set of valid GRUUs to be lost and this specification requires the UA to be robust against such cases. That said, it is possible for a public GRUU to be constructed such that a registrar does not need to retain any additional state for it, yet still meet the requirements described here. 5.4. Creation of a GRUU This section defines additional behaviors associated with the construction and maintenance of a GRUU which are specific to a registrar. These rules do not apply to self-made GRUU or GRUU not obtained through registrations. When a registrar creates a GRUU, it is required to maintain certain information associated with the GRUU, regardless of whether it is a Rosenberg Expires September 6, 2007 [Page 15] Internet-Draft GRUU Mechanism March 2007 public or temporary GRUU. Every GRUU is associated with a single AOR and a single instance ID. A registrar MUST be able to determine the instance ID and AOR when presented with a GRUU. In addition, the GRUU, like an AOR, resolves to zero or more contacts. While the AOR resolves to all registered contacts for an AOR, a GRUU resolves only to those contacts whose instance ID matches the one associated with the GRUU. For this reason, a contact with an instance ID is always bound to both a GRUU and its AOR, never just an AOR or just a GRUU. This is shown pictorially in Figure 5. The figure shows three contacts registered to a single AOR. One of the contacts has an instance ID of 1, and the other two have an instance ID of 2. There are two GRUUs for this AOR. One is associated with instance ID 1, and the other with instance ID 2. The first GRUU resolves only to contacts whose instance ID is one, and the second resolves only to contacts whose instance ID is two. If the contact for instance ID 1 should expire, the AOR would resolve to two contacts, but the GRUU associated with instance ID 1 would resolve to zero. +----------+ +----------+ +----------+ | GRUU | | | | GRUU | | | | AOR | | | |Instance:1| | | |Instance:2| +----------+ +----------+ +----------+ | / | \ / | | / | \ / | | / | \ / | | / | \ / | | / | \ / | | / | \ / | | / | X | | / | / \ | | / | / \ | | / | / \ | V V V V V V +----------+ +----------+ +----------+ | Contact | | Contact | | Contact | | | | | | | |Instance:1| |Instance:2| |Instance:2| +----------+ +----------+ +----------+ Figure 5 There can be multiple GRUUs with the same instance ID and AOR. Indeed, this specification requires registrars to maintain many - one that is public, and several that are temporary. However, if two GRUUs are associated with different AOR or different instance IDs or Rosenberg Expires September 6, 2007 [Page 16] Internet-Draft GRUU Mechanism March 2007 both, the GRUUs MUST be different based on URI equality comparison. A GRUU in a domain MUST NOT be equivalent, based on URI comparison, to any AOR in a domain except for the one associated with the GRUU. A public GRUU will always be equivalent to the AOR based on URI equality rules. The reason is that the rules in RFC 3261 cause URI parameters that are in one URI, but not in the other, to be ignored for equality purposes. Since a public GRUU differs from an AOR only by the presence of the "gr" URI parameter, the two URI are equivalent based on those rules. Once a temporary GRUU is constructed, it MUST be considered valid by the registrar until invalidated based on the rules described previously. Once a temporary GRUU is constructed, it MUST be considered valid for the duration that the AOR itself is valid. Once an AOR is no longer valid within a domain, any of its GRUU MUST be considered invalid as well. This specification does not mandate a particular mechanism for construction of the GRUU. Several example approaches are given in Appendix A. However, in addition to the properties described in Section 3.1, a GRUU constructed by a registrar MUST exhibit the following properties: o The domain part of the URI is an IP address present on the public Internet, or, if it is a host name, the resolution procedures of RFC 3263 [2], once applied, result in an IP address on the public Internet. o When a request is sent to the GRUU, it routes to a proxy that can access the registration data generated by the registrar. Such a proxy is called a authoritative proxy [12]. 5.5. Registration Event Support RFC 3680 [23] defines an event package that allows a client to learn about registration events at the registrar. This package allows registrars to alter registrations forcefully (for example, shortening them to force a re-registration). If a registrar is supporting RFC 3680 and GRUU, it MUST also support [24]. 6. Proxy Behavior Proxy behavior is fully defined in Section 16 of RFC 3261 [1]. GRUU processing impacts that processing in two places -- request targeting at the authoritative proxy and record routing. Rosenberg Expires September 6, 2007 [Page 17] Internet-Draft GRUU Mechanism March 2007 6.1. Request Targeting When a proxy receives a request, owns the domain in the Request-URI, and is supposed to access a Location Service in order to compute request targets (as specified in Section 16.5 of RFC 3261 [1]), the proxy examines the Request-URI. If it contains the "gr" URI parameter but is not equivalent, based on URI comparison, to a currently valid GRUU within the domain, it SHOULD be rejected with a 404; this is the same behavior a proxy would exhibit for any other URI within the domain that is not valid. If the Request-URI contains a the "gr" URI parameter and is equivalent, based on URI comparison, to a GRUU which is currently valid within the domain, processing proceeds as it would for any other URI present in the location service, as defined in Section 16.5 of RFC 3261, except that the "gr" parameter is not removed as part of the canonicalization process. This is the case for both out-of- dialog requests targeted to the GRUU, and mid-dialog requests targeted to the GRUU (in which case the incoming request would have a Route header field value containing the URI that the proxy Record- Routed with). If there are no registered contacts bound to the GRUU, the server MUST return a 480. If there are more than one, the rules described in Section 7 of [12] for selecting a single registered contact apply. Any caller preferences in the request [16] SHOULD be processed against the contacts bound to the GRUU. In essence, to select a registered contact, the GRUU is processed just like it was the AOR, but with only a subset of the contacts bound to the AOR. Special considerations apply to processing of any Path headers stored in the registration [3]. If the received request has Route header field values beyond the one pointing to the authoritative proxy itself (this will happen when the request is a mid-dialog request), the Path URI MUST be discarded. This is permitted by RFC 3327 as a matter of local policy; usage of GRUUs will require this policy in order to avoid call spirals and likely call failures. A proxy MAY apply other processing to the request, such as execution of called party features, as it might do for requests targeted to an AOR. For requests that are outside of a dialog, it is RECOMMENDED to apply screening types of functions, both automated (such as black and white list screening) and interactive (such as interactive voice response (IVR) applications that confer with the user to determine whether to accept a call). In many cases, the new request is related to an existing dialog, and may be an attempt to join it (using the Rosenberg Expires September 6, 2007 [Page 18] Internet-Draft GRUU Mechanism March 2007 Join header field [20]) or replace it (using the Replaces header field [21]). In such cases, the UA will typically make its own authorization decisions. In such cases, bypassing screening services might make sense, but it needs to be carefully considered by network designers, as it depends on the specific type of screening service. However, forwarding services, such as call forwarding, SHOULD NOT be provided for requests sent to a GRUU. The intent of the GRUU is to target a specific UA instance, and this is incompatible with forwarding operations. If the request is a mid-dialog request, a proxy SHOULD only apply services that are meaningful for mid-dialog requests, generally speaking. This excludes screening functions, as well as forwarding ones. In addition, a request sent to a GRUU SHOULD NOT be redirected. In many instances, a GRUU is used by a UA in order to assist in the traversal of NATs and firewalls, and a redirection may prevent such a case from working. 6.2. Record-Routing There are two distinct requirements for record-routing - in the originating domain and in the terminating domain. These requirements avoid unnecessary and possibly problematic spirals of requests. If an originating authoritative proxy receives a dialog-forming request, and the Contact header field contains a GRUU in the domain of the proxy, and that GRUU is associated with the AOR matching the authenticated identity of the requestor (assuming such authentication has been performed), and the request contains Record-Route header fields, the authoritative proxy MUST record route. If the request contained a GRUU in the domain of the proxy, but this GRUU had an AOR which did not match the authenticated identity of the requestor, it is RECOMMENDED that the proxy reject the request with a 403. If a terminating authoritative proxy receives a dialog-forming request, and the Request-URI contains a URI in the location service (either a GRUU or an AOR), and the contact selected for sending the request has an instance ID and is bound to a GRUU, and the registration contain Path URI, the authoritative proxy MUST record route. If a proxy in either the originating or terminating domains but is not an authoritative proxy, the proxy MAY record route. Rosenberg Expires September 6, 2007 [Page 19] Internet-Draft GRUU Mechanism March 2007 Implementors should note that, if a UA uses a GRUU in its contact, and a proxy inserted itself into the Path header field of a registration, that proxy will be receiving mid-dialog requests regardless of whether it record routes or not. The only distinction is what URI the proxy will see in the topmost Route header field of mid-dialog requests. If the proxy record-routes, it will see that URI. If it does not, it will see the Path URI it inserted. 7. Grammar This specification defines two new Contact header field parameters ("temp-gruu" and "pub-gruu") by extending the grammar for "contact- params" as defined in RFC 3261. It also defines a new SIP URI parameter ("gr") by extending the grammar for "uri-parameter" as defined in RFC 3261. contact-params =/ temp-gruu / pub-gruu temp-gruu = "temp-gruu" EQUAL LDQUOT *(qdtext / quoted-pair ) RDQUOT pub-gruu = "pub-gruu" EQUAL LDQUOT *(qdtext / quoted-pair ) RDQUOT uri-parameter =/ gr-param gr-param = "gr" ["=" pvalue] ; defined in RFC3261 The quoted strings for temp-gruu and pub-gruu MUST contain a SIP URI. However, they are encoded like all other quoted strings and can therefore contain quoted-pair escapes when represented this way. 8. Requirements This specification was created in order to meet the following requirements: REQ 1: When a UA invokes a GRUU, it must cause the request to be routed to the specific UA instance to which the GRUU refers. REQ 2: It must be possible for a GRUU to be invoked from anywhere on the Internet, and still cause the request to be routed appropriately. That is, a GRUU must not be restricted to use within a specific addressing realm. Rosenberg Expires September 6, 2007 [Page 20] Internet-Draft GRUU Mechanism March 2007 REQ 3: It must be possible for a GRUU to be constructed without requiring the network to store additional state. REQ 4: It must be possible for a UA to obtain a multiplicity of GRUUs that each route to that UA instance. For example, this is needed to support ad-hoc conferencing where a UA instance needs a different URI for each conference it is hosting. NOTE: This requirement is not met by this specification, and is being addressed in a separate specification. REQ 5: When a UA receives a request sent to a GRUU, it must be possible for the UA to know the GRUU that was used to invoke the request. This is necessary as a consequence of REQ 4. NOTE: This requirement is not met by this specification, and is being addressed in a separate specification. REQ 6: It must be possible for a UA to add opaque content to a GRUU. This content is not interpreted or altered by the network, and is used only by the UA instance to whom the GRUU refers. This provides a basic cookie type of functionality, allowing a UA to build a GRUU with the state embedded. NOTE: This requirement is not met by this specification, and is being addressed in a separate specification. REQ 7: It must be possible for a proxy to execute services and features on behalf of a UA instance represented by a GRUU. As an example, if a user has call blocking features, a proxy may want to apply those call blocking features to calls made to the GRUU, in addition to calls made to the user's AOR. REQ 8: It must be possible for a UA in a dialog to inform its peer of its GRUU, and for the peer to know that the URI represents a GRUU. This is needed for the conferencing and dialog reuse applications of GRUUs, where the URIs are transferred within a dialog. REQ 9: When transferring a GRUU per REQ 8, it must be possible for the UA receiving the GRUU to be assured of its integrity and authenticity. REQ 10: It must be possible for a server that is authoritative for a domain to construct a GRUU which routes to a UA instance bound to an AOR in that domain. In other words, the proxy can construct a GRUU, too. This is needed for the presence application. Rosenberg Expires September 6, 2007 [Page 21] Internet-Draft GRUU Mechanism March 2007 9. Example Call Flow The following call flow, shown in Figure 7, shows a basic registration and call setup, followed by a subscription directed to the GRUU. It then shows a failure of the callee, followed by a re- registration. The conventions of [15] are used to describe representation of long message lines. Caller Proxy Callee | |(1) REGISTER | | |<--------------------| | |(2) 200 OK | | |-------------------->| |(3) INVITE | | |-------------------->| | | |(4) INVITE | | |-------------------->| | |(5) 200 OK | | |<--------------------| |(6) 200 OK | | |<--------------------| | |(7) ACK | | |-------------------->| | | |(8) ACK | | |-------------------->| |(9) SUBSCRIBE | | |-------------------->| | | |(10) SUBSCRIBE | | |-------------------->| | |(11) 200 OK | | |<--------------------| |(12) 200 OK | | |<--------------------| | | |(13) NOTIFY | | |<--------------------| |(14) NOTIFY | | |<--------------------| | |(15) 200 OK | | |-------------------->| | | |(16) 200 OK | | |-------------------->| | | |Crashes, | |(17) REGISTER | Reboots | |<--------------------| | |(18) 200 OK | | |-------------------->| Rosenberg Expires September 6, 2007 [Page 22] Internet-Draft GRUU Mechanism March 2007 Figure 7 The Callee supports the GRUU extension. As such, its REGISTER (1) looks like: REGISTER sip:example.com SIP/2.0 Via: SIP/2.0/UDP 192.0.2.1;branch=z9hG4bKnashds7 Max-Forwards: 70 From: Callee ;tag=a73kszlfl Supported: gruu To: Callee Call-ID: 1j9FpLxk3uxtm8tn@192.0.2.1 CSeq: 1 REGISTER Contact: ;+sip.instance="" Content-Length: 0 The registrar assigns a temporary and a public GRUU. The REGISTER response (message 2) would look like: SIP/2.0 200 OK Via: SIP/2.0/UDP 192.0.2.1;branch=z9hG4bKnashds7 From: Callee ;tag=a73kszlfl To: Callee ;tag=b88sn Call-ID: 1j9FpLxk3uxtm8tn@192.0.2.1 CSeq: 1 REGISTER Contact: ;pub-gruu="sip:callee@example.com ;gr=urn:uuid:f81d4fae-7dec-11d0-a765-00a0c91e6bf6" ;temp-gruu="sip:pig8a788@example.com;gr" ;+sip.instance="" ;expires=3600 Content-Length: 0 Note how the Contact header field in the REGISTER response contains the pub-gruu parameter with the public GRUU sip:callee@ example.com;gr=urn:uuid:f81d4fae-7dec-11d0-a765-00a0c91e6bf6, and the temp-gruu parameter with the temporary GRUU sip:pig8a788@example.com;gr. Both are valid GRUUs for the AOR and instance ID, and both translate to the contact sip:callee@192.0.2.1. The INVITE from the caller (message 3) is a normal SIP INVITE. However, the 200 OK generated by the callee (message 5) now contains a GRUU as the remote target. The UA has chosen to use its public Rosenberg Expires September 6, 2007 [Page 23] Internet-Draft GRUU Mechanism March 2007 GRUU. SIP/2.0 200 OK Via: SIP/2.0/UDP proxy.example.com;branch=z9hG4bKnaa8 Via: SIP/2.0/UDP host.example.com;branch=z9hG4bK99a From: Caller ;tag=n88ah To: Callee ;tag=a0z8 Call-ID: 1j9FpLxk3uxtma7@host.example.com CSeq: 1 INVITE Supported: gruu Allow: INVITE, OPTIONS, CANCEL, BYE, ACK, SUBSCRIBE Contact: Content-Length: -- Content-Type: application/sdp [SDP Not shown] At some point later in the call, the caller decides to subscribe to the dialog event package [14] at that specific UA. To do that, it generates a SUBSCRIBE request (message 9), but directs it towards the remote target, which is a GRUU: SUBSCRIBE sip:callee@example.com;gr=urn:uuid:f8 1d4fae-7dec-11d0-a765-00a0c91e6bf6 SIP/2.0 Via: SIP/2.0/UDP host.example.com;branch=z9hG4bK9zz8 From: Caller ;tag=kkaz- To: Call-ID: faif9a@host.example.com CSeq: 2 SUBSCRIBE Supported: gruu Event: dialog Allow: INVITE, OPTIONS, CANCEL, BYE, ACK, NOTIFY Contact: Content-Length: 0 In this example, the caller itself supports the GRUU extension, and Rosenberg Expires September 6, 2007 [Page 24] Internet-Draft GRUU Mechanism March 2007 is using its own GRUU to populate its remote target. This request is routed to the proxy, which proceeds to perform a location lookup on the Request-URI. It is translated into the contact for that instance, and then proxied to that contact. SUBSCRIBE sip:callee@192.0.2.1 SIP/2.0 Via: SIP/2.0/UDP proxy.example.com;branch=z9hG4bK9555 Via: SIP/2.0/UDP host.example.com;branch=z9hG4bK9zz8 From: Caller ;tag=kkaz- To: Call-ID: faif9a@host.example.com CSeq: 2 SUBSCRIBE Supported: gruu Event: dialog Allow: INVITE, OPTIONS, CANCEL, BYE, ACK, NOTIFY Contact: Content-Length: 0 The SUBSCRIBE generates a 200 response (message 11), which is followed by a NOTIFY (message 13 and 14) and its response (message 15 and 16). At some point after message 16 is received, the callee's machine crashes and recovers. It obtains a new IP address, 192.0.2.2. Unaware that it had previously had an active registration, it creates a new one (message 17 below). Notice how the instance ID remains the same, as it persists across reboot cycles: REGISTER sip:example.com SIP/2.0 Via: SIP/2.0/UDP 192.0.2.2;branch=z9hG4bKnasbba Max-Forwards: 70 From: Callee ;tag=ha8d777f0 Supported: gruu To: Callee Call-ID: hf8asxzff8s7f@192.0.2.2 CSeq: 1 REGISTER Contact: ;+sip.instance="" Content-Length: 0 The registrar notices that a different contact, sip:callee@192.0.2.1, Rosenberg Expires September 6, 2007 [Page 25] Internet-Draft GRUU Mechanism March 2007 is already associated with the same instance ID. It registers the new one too and returns both in the REGISTER response. Both have the same public GRUUs, but the registrar has generated a second temporary GRUU for this AOR and instance ID combination. Both contacts are included in the REGISTER response, and the temporary GRUU for each is the same - the most recently created one for the instance ID and AOR. The registrar then generates the following response: SIP/2.0 200 OK Via: SIP/2.0/UDP 192.0.2.2;branch=z9hG4bKnasbba From: Callee ;tag=ha8d777f0 To: Callee ;tag=99f8f7 Call-ID: hf8asxzff8s7f@192.0.2.2 CSeq: 1 REGISTER Contact: ;pub-gruu="sip:callee@example.com;gr=urn: uuid:f81d4fae-7dec-11d0-a765-00a0c91e6bf6" ;temp-gruu="sip:asd98fggg7example.com;gr" ;+sip.instance="" ;expires=3600 Contact: ;pub-gruu="sip:callee@example.com;gr=urn: uuid:f81d4fae-7dec-11d0-a765-00a0c91e6bf6" ;temp-gruu="sip:asd98fggg7example.com;gr" ;+sip.instance="" ;expires=400 Content-Length: 0 There is no need for the UA to remove the stale registered contact; the request targeting rules in [12] will cause the request to be delivered to the most recent one. 10. Security Considerations Attacks in SIP networks using GRUUs can be divided into inside attacks (where the attacker is a valid participant in the system but is malicious), and outside attacks, where a third party is trying to attack the system. In addition, there are privacy considerations with using GRUUs. Rosenberg Expires September 6, 2007 [Page 26] Internet-Draft GRUU Mechanism March 2007 10.1. Outside Attacks It is important for a UA to be assured of the integrity of a GRUU given in a REGISTER response. If the GRUU is tampered with by an attacker, the result could be denial of service to the UA. As a result, it is RECOMMENDED that a UA use the SIPS URI scheme in the Request-URI when registering. Proxies and registrars MUST support the sips URI and MUST support TLS. Note that this does not represent a change from the requirements in RFC 3261. The example GRUU construction algorithm in Appendix A.1 makes no attempt to create a GRUU that hides the AOR and instance ID associated with the GRUU. In general, determination of the AOR associated with a GRUU is considered a good property, since it allows for easy tracking of the target of a particular call. Learning the instance ID provides little benefit to an attacker. To register or otherwise impact registrations for the user, an attacker would need to obtain the credentials for the user. Knowing the instance ID is insufficient. The example GRUU construction algorithm in Appendix A.1 makes no attempt to create a GRUU that prevents users from guessing a GRUU based on knowledge of the AOR and instance ID. A user that is able to do that will be able to direct a new request at a particular instance. However, this specification recommends that service treatment (in particular, screening features) be given to requests that are sent to a GRUU. That treatment will make sure that the GRUU does not provide a back door for attackers to contact a user that has tried to block the attacker. 10.2. Inside Attacks As a consequence of this specification, a UA will begin using GRUUs in the dialog forming and target refresh requests and responses it emits. These GRUUs will be passed to other UA (called the correspondent), which then use them in requests that they emit. These UA might be malicious, and attempt to remove the "gr" parameter from the URI before using it. Consequently, consideration must be given to the effect of such removal. If a malicious correspondent removes the "gr" URI parameter, the request will be routed to the authoritative proxy. If the GRUU had been temporary, removal of the "gr" parameter produces a URI that is not recognized as a GRUU and not equal to any AOR. The request will be rejected. If the GRUU had been public, the resulting of removing the "gr" parameter produces the AOR. Therefore, the request is treated like a call to the AOR. Since it is a desired goal to allow users to extract the AOR from the GRUU, this is not an attack and the Rosenberg Expires September 6, 2007 [Page 27] Internet-Draft GRUU Mechanism March 2007 call will be handled normally. A malicious user in the system might try to use a GRUU for launching a DoS attack against another SIP UA. To do that, it would wait for a call from that UA, from it, observe their GRUU. Once obtained, the UA would launch a SIP request to an entity, such as a presence server, which will generate many requests back towards the UA. However, the attacker will use the target's GRUU in the Contact header field of that SUBSCRIBE request. This will cause the traffic to be directed towards the target instead. Since the GRUU is globally routable, such traffic is more likely to be delivered to the target than traffic sent to its IP address. This specification helps mitigate this attack by requiring proxies to validate that the GRUU in the Contact of a request matches the authenticated identity of the sender of the request. This check requires the use of an outbound proxy. 10.3. Privacy Considerations RFC 3323 defines mechanisms for privacy. It distinguishes between user-provided privacy and network-provided privacy. In the latter, the user requests privacy services from the network by including a Privacy header field in the request. In the former, the UA follows a basic set of guidelines for construction of its request so let a certain level of privacy is afforded. The guidelines in Section 4.1 of RFC 3323 for user-provided privacy request that a UA construct its Contact header field with a URI that omits a user part, and utilizes the IP address or hostname of the UA. Such recommendations are in conflict with the rules defined in this specification, which require the usage of a GRUU in the Contact header field. However, the temporary GRUUs provided by the registrar can be used in place of the Contact URI format described in RFC 3323. A user agent would gather the temporary GRUU returned in each REGISTER responses, and keep a small number of them cached. When it makes or receives a call, a temporary GRUU is used to populate the Contact header field. A UA can either elect to use the same temporary GRUU in each call, or it can use a different temporary GRUU in each call. The choice depends on the level of privacy desired: o A UA utilizing the same temporary URI for each call will allow a correspondent, based solely on investigation of the Contact header field, to correlate calls as coming from the same UA. Note that this is also true for the user provided privacy procedures in RFC 3323, since the IP address or hostname in the Contact URI provides Rosenberg Expires September 6, 2007 [Page 28] Internet-Draft GRUU Mechanism March 2007 a similar correlator. o A UA utilizing a different temporary URI for each call will not allow a correspondent, based solely on investigation of the Contact header field, to correlate calls as coming from the same UA. o In both cases, absent network-provided privacy, IP address and port information in the Session Description Protocol (SDP) [10] will allow a correspondent to correlate calls as coming from the same UA. o In both cases, if a user makes a call, the correspondent will be able to call back by directing requests towards the GRUU in the Contact header field. Similarly, features such as transfer and digit collection by network application servers [19], which depend on a Contact with the GRUU property, will also be possible. These kinds of inbound requests will be possible until the registration for that UA lapses. A UA that wishes to invalidate its previous temporary GRUU in order to limit reachability MAY do so by generating a REGISTER refresh with a Call-ID that differs from ones used previously. A UA SHOULD NOT forcefully expire its registration and then re-register in order to invalidate temporary a GRUU; this results in a brief period of unreachability and will often produce excess load on the network. Refreshing with a new Call-ID is more efficient and is meant as the technique for coarse-grained control over the validity of temporary GRUU. A UA wishing to not be disturbed by a specific call back will need to implement manual or automated call handling procedures to reject it. This specification does not provide the UA the ability to manually invalidate individual temporary GRUU. If a UA insists on not receiving any such inbound requests (including ones generated by network applications, such as those used for collecting digits), the UA can place a non-GRUU into the Contact header field. However, this is NOT RECOMMENDED. Usage of a GRUU coupled with automated call rejection features is far superior. o As long as a temporary GRUU is used to populate the Contact header field, a correspondent will not be able to ascertain any information about the AOR or instance ID of the UA by inspection of the Contact header field. However, absent a network-provided privacy service, the IP address in the SDP can be used to determine information about the UA, such as its geographic location and ISP. o In all cases, regardless of whether the UA uses a temporary or public GRUU in the Contact, regardless of whether it utilizes GRUU at all, and regardless of whether it invokes a network-provided Rosenberg Expires September 6, 2007 [Page 29] Internet-Draft GRUU Mechanism March 2007 privacy service, a correspondent will be able to determine the SIP service provider of the UA. 11. IANA Considerations This specification defines two new Contact header field parameters, one SIP URI parameter, and a SIP option tag. 11.1. Header Field Parameter This specification defines two new header field parameters, as per the registry created by [8]. The required information is as follows: Header field in which the parameter can appear: Contact Name of the Parameter: pub-gruu RFC Reference: RFC XXXX [[NOTE TO IANA: Please replace XXXX with the RFC number of this specification.]] Header field in which the parameter can appear: Contact Name of the Parameter: temp-gruu RFC Reference: RFC XXXX [[NOTE TO IANA: Please replace XXXX with the RFC number of this specification.]] 11.2. URI Parameter This specification defines one new SIP URI parameter, as per the registry created by [9]. Name of the Parameter: gr Predefined Values: none RFC Reference: RFC XXXX [[NOTE TO IANA: Please replace XXXX with the RFC number of this specification.]] 11.3. SIP Option Tag This specification registers a new SIP option tag, as per the guidelines in Section 27.1 of RFC 3261. Rosenberg Expires September 6, 2007 [Page 30] Internet-Draft GRUU Mechanism March 2007 Name: gruu Description: This option tag is used to identify the Globally Routable User Agent URI (GRUU) extension. When used in a Supported header, it indicates that a User Agent understands the extension. When used in a Require header field of a REGISTER request, it indicates that the registrar shouldn't process the registration unless it supports the GRUU extension. 12. Acknowledgements The author would like to thank Eric Rescorla, Robert Sparks, Rohan Mahy, Paul Kyzivat, Alan Johnston, Ya-Ching Tan, Dale Worley, Jeroen van Bemmel, Vijay Gurbani, Andrew Allen, Alan Hawrylyshen, Francois Audet, Fredrik Thulin, Dean Willis, David Hancock, Keith Drage, and Cullen Jennings for their comments and contributions to this work. Eric Rescorla provided the text for the introduction and the GRUU construction algorithm in the appendix. 13. References 13.1. Normative References [1] Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston, A., Peterson, J., Sparks, R., Handley, M., and E. Schooler, "SIP: Session Initiation Protocol", RFC 3261, June 2002. [2] Rosenberg, J. and H. Schulzrinne, "Session Initiation Protocol (SIP): Locating SIP Servers", RFC 3263, June 2002. [3] Willis, D. and B. Hoeneisen, "Session Initiation Protocol (SIP) Extension Header Field for Registering Non-Adjacent Contacts", RFC 3327, December 2002. [4] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [5] Roach, A., "Session Initiation Protocol (SIP)-Specific Event Notification", RFC 3265, June 2002. [6] Sparks, R., "The Session Initiation Protocol (SIP) Refer Method", RFC 3515, April 2003. [7] Rosenberg, J., Schulzrinne, H., and P. Kyzivat, "Indicating User Agent Capabilities in the Session Initiation Protocol (SIP)", RFC 3840, August 2004. Rosenberg Expires September 6, 2007 [Page 31] Internet-Draft GRUU Mechanism March 2007 [8] Camarillo, G., "The Internet Assigned Number Authority (IANA) Header Field Parameter Registry for the Session Initiation Protocol (SIP)", BCP 98, RFC 3968, December 2004. [9] Camarillo, G., "The Internet Assigned Number Authority (IANA) Uniform Resource Identifier (URI) Parameter Registry for the Session Initiation Protocol (SIP)", BCP 99, RFC 3969, December 2004. [10] Handley, M., Jacobson, V., and C. Perkins, "SDP: Session Description Protocol", RFC 4566, July 2006. [11] Schulzrinne, H., "The tel URI for Telephone Numbers", RFC 3966, December 2004. [12] Jennings, C. and R. Mahy, "Managing Client Initiated Connections in the Session Initiation Protocol (SIP)", draft-ietf-sip-outbound-07 (work in progress), January 2007. 13.2. Informative References [13] Peterson, J., "A Privacy Mechanism for the Session Initiation Protocol (SIP)", RFC 3323, November 2002. [14] Rosenberg, J., Schulzrinne, H., and R. Mahy, "An INVITE- Initiated Dialog Event Package for the Session Initiation Protocol (SIP)", RFC 4235, November 2005. [15] Sparks, R., Hawrylyshen, A., Johnston, A., Rosenberg, J., and H. Schulzrinne, "Session Initiation Protocol (SIP) Torture Test Messages", RFC 4475, May 2006. [16] Rosenberg, J., Schulzrinne, H., and P. Kyzivat, "Caller Preferences for the Session Initiation Protocol (SIP)", RFC 3841, August 2004. [17] Schulzrinne, H., "Dynamic Host Configuration Protocol (DHCP- for-IPv4) Option for Session Initiation Protocol (SIP) Servers", RFC 3361, August 2002. [18] Sparks, R., "Session Initiation Protocol Call Control - Transfer", draft-ietf-sipping-cc-transfer-07 (work in progress), October 2006. [19] Burger, E. and M. Dolly, "A Session Initiation Protocol (SIP) Event Package for Key Press Stimulus (KPML)", RFC 4730, November 2006. Rosenberg Expires September 6, 2007 [Page 32] Internet-Draft GRUU Mechanism March 2007 [20] Mahy, R. and D. Petrie, "The Session Initiation Protocol (SIP) "Join" Header", RFC 3911, October 2004. [21] Mahy, R., Biggs, B., and R. Dean, "The Session Initiation Protocol (SIP) "Replaces" Header", RFC 3891, September 2004. [22] Willis, D. and B. Hoeneisen, "Session Initiation Protocol (SIP) Extension Header Field for Service Route Discovery During Registration", RFC 3608, October 2003. [23] Rosenberg, J., "A Session Initiation Protocol (SIP) Event Package for Registrations", RFC 3680, March 2004. [24] Kyzivat, P., "Registration Event Package Extension for Session Initiation Protocol (SIP) Globally Routable User Agent URIs (GRUUs)", draft-ietf-sipping-gruu-reg-event-08 (work in progress), October 2006. [25] Rescorla, E., "How to Implement Secure (Mostly) Stateless Tokens", draft-rescorla-stateless-tokens-01 (work in progress), March 2007. Appendix A. Example GRUU Construction Algorithms The mechanism for constructing a GRUU is not subject to specification. This appendix provides two examples that can be used by a registar. Of course, others are permitted, as long as they meet the constraints defined for a GRUU. A.1. Public GRUU Algorithm The most basic approach for constructing a public GRUU is to take the AOR, and place the actual value of the instance ID into the contents of the "gr" URI parameter. A.2. Temporary GRUU This specification requires a registrar to create a new temporary GRUU on each registration refresh. If a registration is very long lived, this can quickly result in hundreds or even thousands of temporary GRUUs being created and allocated to a UA. Consequently, it is important to have an algorithm for constructing temporary GRUUs which does not require additional storage that grows in size with the number of temporary GRUUs. The following algorithm meets this goal. When the first contact with a specific instance ID is registered, the registrar notes the wallclock time (W) and stores this as part of the Rosenberg Expires September 6, 2007 [Page 33] Internet-Draft GRUU Mechanism March 2007 registration. When the registrar wishes to create a new temporary GRUU, it constructs a state token using the procedures defined in [25]. The input to this procedure is a string S representing the state to be stashed in the token. The registrar constructs S as: S = (AOR || " " || instance_ID || Call-ID || W || T1 || T2 || .. || Tn) Where || indicates concatenation, and T1, T2, and so on represent the current expiration times (measured in absolute time) of each contact with that instance ID. Call-ID represents the Call-ID of the most recently registered contact for that AOR and instance ID. Usage of the current expiration times allows a new value for S to be produced whenever a contact for that particular instance ID is refreshed, since a refresh always changes the expiration time. The stateless tokens in [25] include an expiration time and sequence number. Expiration of temporary GRUU is determined through data within the state string S, and consequently, these fields can be set to zero. The GRUU is then constructed as: user-part = "GRUU" || BASE64(T) Where T is the token generated in [25] using string S. This mechanism uses the user-part of the SIP URI to convey the encrypted AOR and instance ID. The URI contains the "gr" parameter without a value, and the domain part is the domain of the provider. When the authoritative proxy receives a request addressed to the GRUU, it: o Decrypts it and verifies it as described in [25] o Extracts the string S stashed in the token o Checks the value of W against the current value stored for that instance ID and AOR: * If they match, the proxy extracts the value of Call-ID from S, and checks it against the Call-ID value of the most recently registered contact for that AOR and instance ID: + If they match, the GRUU is valid. Rosenberg Expires September 6, 2007 [Page 34] Internet-Draft GRUU Mechanism March 2007 + If they don't match, the UA has invalidated this GRUU by changing the Call-ID, and the GRUU is invalid. * If they don't match, the GRUU was allocated in a previous registration cycle and is no longer valid. The benefit of this mechanism is that a registrar need not store additional information on mapping a GRUU to its corresponding contact. The user-part of the GRUU contains the instance ID and AOR. Assuming that the domain stores registrations in a database indexed by the AOR, the proxy processing the GRUU would look up the AOR, extract the currently registered contacts, and find the one that matches the instance ID encoded in the Request-URI. The contact whose instance ID is that instance ID is then used as the translated version of the GRUU. Message integrity is needed to prevent attacks whereby the proxy is sent requests with fake GRUUs, causing it to direct requests to any named URI. While this approach has many benefits, it has the drawback of producing very long GRUUs due to the non-trivial amount of information that is encrypted. Appendix B. Network Design Considerations The GRUU specification works properly based on logic implemented at the user agents and in the authoritative proxies on both sides of a call. Consequently, it is possible to construct network deployments in which GRUUs will not work properly. One important assumption made by the GRUU mechanism is that, if a request passes through any proxies in the originating domain prior to visiting the terminating domain, one of those proxies will be the authoritative proxy for the UAC. Administrators of SIP networks will need to make sure that this property is retained. There are several ways it can be accomplished: 1. If the user agents support the service route mechanism [22], the registrar can implement it and return a service route that points to the authoritative proxy. This will cause requests originated by the user agent to pass through the authoritative proxy. 2. The user agents can be configured to never use an outbound proxy, and send requests directly to the domain of the terminating party. This configuration is not practical in many use cases but it is a solution to this requirement. Rosenberg Expires September 6, 2007 [Page 35] Internet-Draft GRUU Mechanism March 2007 3. The user agents can be configured with an outbound proxy in the same domain as the authoritative proxy, and this outbound proxy forwards requests to the authoritative proxy by default. This works very well in cases where the clients are not roaming; in such cases the outbound proxy in a visited network may be discovered dynamically through DHCP [17]. 4. In cases where the client discovers a local outbound proxy via a mechanism such as DHCP, and is not implementing service route, the UA can be configured to automatically add an additional Route header field after the outbound proxy, which points to a proxy in the home network. This has the same net effect of service route, but is accomplished through static configuration. Author's Address Jonathan Rosenberg Cisco Edison, NJ US Email: jdrosen@cisco.com URI: http://www.jdrosen.net Rosenberg Expires September 6, 2007 [Page 36] Internet-Draft GRUU Mechanism March 2007 Full Copyright Statement Copyright (C) The IETF Trust (2007). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Intellectual Property The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org. Acknowledgment Funding for the RFC Editor function is provided by the IETF Administrative Support Activity (IASA). Rosenberg Expires September 6, 2007 [Page 37]