Pseudo-Wire Edge-to-Edge Emulation D. Zelig, Ed. Internet-Draft Corrigent Systems Intended status: Standards Track R. Cohen, Ed. Expires: April 25, 2007 Resolute Networks T. Nadeau, Ed. Cisco Systems, Inc. October 22, 2006 SONET/SDH Circuit Emulation Service Over Packet (CEP) Management Information Base Using SMIv2 draft-ietf-pwe3-cep-mib-09 Status of this Memo By submitting this Internet-Draft, each author represents that any applicable patent or other IPR claims of which he or she is aware have been or will be disclosed, and any of which he or she becomes aware will be disclosed, in accordance with Section 6 of BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. This Internet-Draft will expire on April 25, 2007. Copyright Notice Copyright (C) The Internet Society (2006). Abstract This memo defines an experimental portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it describes managed objects for modeling SONET/SDH circuits over a Packet Switch Network (PSN). Zelig, et al. Expires April 25, 2007 [Page 1] Internet-Draft PW CEP MIB October 2006 Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 3 3. Co-Authors . . . . . . . . . . . . . . . . . . . . . . . . . . 4 4. The Internet-Standard Management Framework . . . . . . . . . . 4 5. Feature Checklist . . . . . . . . . . . . . . . . . . . . . . 4 6. MIB Module Usage . . . . . . . . . . . . . . . . . . . . . . . 5 6.1. PW MIB Modules Usage . . . . . . . . . . . . . . . . . . . 5 6.2. PW CEP MIB Summary . . . . . . . . . . . . . . . . . . . . 6 6.3. PW CEP MIB Module Usage . . . . . . . . . . . . . . . . . 6 6.4. Example of CEP MIB Usage . . . . . . . . . . . . . . . . . 7 7. Object Definitions . . . . . . . . . . . . . . . . . . . . . . 9 8. Security Considerations . . . . . . . . . . . . . . . . . . . 67 9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 68 10. References . . . . . . . . . . . . . . . . . . . . . . . . . . 68 10.1. Normative References . . . . . . . . . . . . . . . . . . . 68 10.2. Informative References . . . . . . . . . . . . . . . . . . 69 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 69 Intellectual Property and Copyright Statements . . . . . . . . . . 71 Zelig, et al. Expires April 25, 2007 [Page 2] Internet-Draft PW CEP MIB October 2006 1. Introduction This document describes a model for managing encapsulated SONET Time Division Multiplexed (TDM) digital signals for transmission over a Packet Switched Network (PSN). This document is closely related to [CEP], which describes the technology to encapsulate TDM signals and provide the Circuit Emulation Service over a Packet Switched Network (PSN). The model for CEP management is a MIB module. The CEP MIB module described in this document works closely with the MIB modules described in [PWMIB] and the textual conventions defined in [PWTC]. In the spirit of the [RFC2863], a CEP connection will be a pseudo- wire (PW), and will therefore not be represented in the ifTable. CEP is currently specified to carry "structured" SONET paths, meaning that each SONET PATH/VT within the section/line/path can be processed separately. The SONET section/line/path interface stack is modeled within [RFC3592]. This document adopts the definitions, acronyms and mechanisms described in [RFC3985]. Unless otherwise stated, the mechanisms of [RFC3985] apply and will not be re-described here. Comments should be made directly to the PWE3 mailing list at pwe3@ietf.org. Conventions used in this document The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC-2119 [BCP14]. 2. Terminology CEP terminology comes from [CEP] that describes a mechanism for transporting SONET Time Division Multiplexed (TDM) digital signals over a packet-oriented network. The mechanism for structured (as outlined in the CEP draft) terminates the SONET section and line overhead and then breaks the SONET path's Synchronous Payload Envelope (SPE) into fragments for transmission over a PSN. Mechanism for terminating of the SONET path overhead and extracting SONET VTs are also described in [CEP]. Mechanisms for Fractional SONET SPE emulation are described in [CEP]. A CEP header is appended at the beginning of each fragment to provide information regarding where the SPE begins within the packet stream, a sequence number, and pointer Zelig, et al. Expires April 25, 2007 [Page 3] Internet-Draft PW CEP MIB October 2006 adjustment information (see [CEP]). "Outbound" references the traffic direction where a SONET path's payload (SPE) is received, adapted to packet, assigned a PW label, and sent into the PSN. Conversely, "inbound" is the direction where packets are received from the PSN, packet payloads are reassembled back into an SPE, and inserted as a SONET path into the SONET section and line. Since A SONET path is bi-directional and symmetrical, CEP uses the same SONET time-slot, SONET width and packet size. Inbound and outbound PW labels may differ. 3. Co-Authors The individuals listed below are co-authors of this document. Dave Danenberg was the editor of this document at the pre-WG versions of the PW MIB modules. Andrew G. Malis - Tellabs Dave Danenberg - Litchfield Communications Scott C. Park - Litchfield Communications 4. The Internet-Standard Management Framework For a detailed overview of the documents that describe the current Internet-Standard Management Framework, please refer to section 7 of [RFC3410]. Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. MIB objects are generally accessed through the Simple Network Management Protocol (SNMP). Objects in the MIB are defined using the mechanisms defined in the Structure of Management Information (SMI). This memo specifies a MIB module that is compliant to the SMIv2, which is described in STD 58,[RFC2578], STD 58, [RFC2579] and STD 58, [RFC2580]. 5. Feature Checklist The PW CEP MIB module (PW-CEP-STD-MIB) is designed to satisfy the following requirements and constraints: Zelig, et al. Expires April 25, 2007 [Page 4] Internet-Draft PW CEP MIB October 2006 - The MIB module is designed to be work with the PW-STD-MIB [PWMIB]. - The MIB module is independent of the PSN type. - The MIB module supports all the signal types as defined in [CEP]: SPE, fractional SPE, VT, both SONET and SDH mapping and all the optional faetures as defined in [CEP]. - The MIB module reports all the statistics as defined by [CEP]. 6. MIB Module Usage 6.1. PW MIB Modules Usage The MIB module structure for defining a PW service is composed of three layers of MIB modules functioning together. This general model is defined in the PWE3 architecture [RFC3985]. The layering model is intended to sufficiently isolate PW services from the underlying PSN layer that carries the emulated service. This is done at the same time as providing a standard means for connecting any supported services to any supported PSNs. The first layer, known as the service layer, contains service- specific modules such as the one defined in this document. These modules define service-specific management objects that interface or collaborate with existing MIB modules for the native version of the service. The service-specific module "glues" the standard modules to the PWE3 MIB modules. The PW-CEP-STD-MIB module defined in this memo serves as one of the PW type-specific MIB module. The next layer of the PWE3 MIB framework is the PW MIB module [PWMIB]. This module is used to configure general parameters of PWs that are common to all types of emulated services and PSNs. This layer is connected to the service-specific layer above, and the PSN layer below. The PSN layer provides PSN-specific modules for each type of PSN. These modules associate the PW with one or more "tunnels" that carry the service over the PSN. These modules are defined in other documents. This module is used to "glue" the PW service to the underlying PSN-specific MIB modules. [PWTC] defines some of the object types used in these modules. For clarity of the description below, in most cases we refer to the PATH SONET signal configuration only. When configuring VT mode as described in [RFC3985], the same apply for the VT level. Zelig, et al. Expires April 25, 2007 [Page 5] Internet-Draft PW CEP MIB October 2006 6.2. PW CEP MIB Summary - The CEP PW Table (pwCepTable) contains the SONET Path/VT ifIndex, SONET Path Time slot, the pwCepCfgTable index, config error indications, and various status indications. - The CEP PW Configuration Parameter Table (pwCepCfgTable) has objects for CEP PW configuration. In situations where sets of config objects are common amongst more than 1 CEP PW, a single entry here may be referenced by many pwCepTable entries. - The CEP Performance Current Table (pwCemPerfCurrentTable) contains CEP stats for the current 15-minute period. - The CEP Performance 15 Minute Interval Table (pwCemPerfIntervalTable) is similar to the pwCemPerfCurrentTable. It contains historical intervals (usually 96 15-minute entries to cover a 24 hour period). Note: the performance interval statistics are supported by CEP due to the very function of CEP - that is, processing SONET. See [RFC3592]. - The CEP Performance 1 day Table (pwCepPerf1DayTable) contains statistics accumulated during the current day and contains previous days historical statistics. - The CEP Fractional Table (pwCepFracTable) adds configuration and monitoring parameters for fractional SPE PWs. - The Conformance Config Table (pwCepConformanceCfgTable) allows the vendor to specify the extent to which certain objects are supported (or not). 6.3. PW CEP MIB Module Usage Configuring a CEP PW involves the following steps. First create an entry in the pwTable: - Follow steps as defined in [PWMIB]. Configure the PSN tunnel in the respective PSN specific PWE3 PSN glue MIB module and the respective PSN specific MIB modules. Configure the SONET Path parameters: Zelig, et al. Expires April 25, 2007 [Page 6] Internet-Draft PW CEP MIB October 2006 - Set the SONET path width in the sonetPathCurrentTable [RFC3592]. - Set the SONET path index and the SONET path starting time slot in the pwCepTable. NOTE: The agent will have created an entry in the pwCepTable based on the entry created in the pwTable. Configure the CEP PW: - If necessary, create an entry in the pwCepCfgTable (a suitable entry may already exist). Set packet length, etc. - Set the index of this pwCepCfgTable entry in the pwCepTable. Observe the CEP PW: - Once a CEP PW is operational, the pwCepPerfCurrentTable, pwCepPerfIntervalTable, and pwCepPerf1DayTable can be used to monitor the various counts, indicators, and conditions of the PW. Conforming to the CEP MIB objects: - The pwCepConformanceCfgTable is used to state True/False whether certain objects are supported. An ASCII string object is available with every True/False object as a means to explain the extent of 'true' support, or perhaps explain why the 'false' was set. 6.4. Example of CEP MIB Usage In this section we provide an example of using the MIB objects described in Section 7 to set up a CEP PW (width of 3 STSs, starting at time slot 1). While this example is not meant to illustrate every permutation of the MIB, it is intended as an aid to understanding some of the key concepts. It is meant to be read after going through the MIB itself. See [PWMIB] for an example of setting up PSN Tunnels. First configure the SONET path width, starting time-slot, and associated CEP PW. In this case, an STS-3c starts at SONET time slot 1 (and is distributed normally within the SONET frame). In the following example, the ifIndex for the sonetPathCurrentEntry is 23, while the pwCepCfgTable index is 9. In [RFC3592] sonetPathCurrentEntry (ifIndex = 23) : Zelig, et al. Expires April 25, 2007 [Page 7] Internet-Draft PW CEP MIB October 2006 { sonetPathCurrentWidth = 3, sonetPathCurrentStatus ... ... } Create an entry in the pwCepCfgTable (index = 9) : { pwCepCfgSonetPaylaodLength = 783 -- payload bytes pwCepCfgMinPktLength = 0 -- no minimum pwCepCfgPktReorder = true pwCepCfgEnableDBA = unequipped pwCepCfgRtpHdrSuppress = false pwCepCfgJtrBfrDepth = 500 -- micro-seconds pwCepCfgConsecPktsInsync = 2 -- Exit LOPS state pwCepCfgConsecMissingOutSync = 10 -- Enter LOPS state pwCepCfgPktErrorPlayOutValue = 0xFF -- All ones pwCepCfgMissingPktsToSes = 3 -- packets, pwCepCfgSesToUas = 2 -- seconds, pwCepCfgSecsToExitUas = 10 -- seconds, pwCepCfgRowStatus = createAndGo } Check that there is no error bit set in pwCepConfigError. In the PW-STD-MIB module: Get a new index and create a new pwTable entry using pwIndexNext (here, the PW index = 83) and pwRowStatus. In this new entry, set pwType to 'cep'. This should create a new entry in the pwCepTable. Set up and the SONET path ifIndex, SONET path time slot, and Cfg Table indexes within this new pwCep table entry: { pwCepSonetIfIndex = 23 -- Index of associated entry -- in sonetPathCurrent table. pwCepCfgIndex = 9 -- Index of associated entry -- in pwCepCfg table (above). } Zelig, et al. Expires April 25, 2007 [Page 8] Internet-Draft PW CEP MIB October 2006 7. Object Definitions PW-CEP-STD-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Counter32, Unsigned32, Counter64, transmission FROM SNMPv2-SMI -- [RFC2578] MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF -- [RFC2580] TEXTUAL-CONVENTION, TruthValue, RowStatus, StorageType, TimeStamp FROM SNMPv2-TC -- [RFC2579] SnmpAdminString FROM SNMP-FRAMEWORK-MIB -- [RFC3411] InterfaceIndexOrZero, InterfaceIndex FROM IF-MIB -- [RFC2863] PerfCurrentCount, PerfIntervalCount FROM PerfHist-TC-MIB -- [RFC3593] HCPerfCurrentCount, HCPerfIntervalCount, HCPerfTimeElapsed, HCPerfValidIntervals FROM HC-PerfHist-TC-MIB -- [RFC3705] pwIndex FROM PW-STD-MIB -- [RFCyyyy] -- RFC Editor: Please replace yyyy with actual RFC number and -- remove this note PwCfgIndexOrzero FROM PW-TC-STD-MIB -- [RFCyyyy] -- RFC Editor: Please replace yyyy with actual RFC number and -- remove this note ; -- The PW CEP MIB pwCepStdMIB MODULE-IDENTITY LAST-UPDATED "200610171200Z" -- 17 October 2006 12:00:00 GMT ORGANIZATION "Pseudo-Wire Emulation Edge-to-Edge (PWE3) Working Group" Zelig, et al. Expires April 25, 2007 [Page 9] Internet-Draft PW CEP MIB October 2006 CONTACT-INFO " David Zelig (Ed.) E-mail: davidz@corrigent.com Ron Cohen (Ed.) Email: ronc@resolutenetworks.com Thomas D. Nadeau (Ed.) Email: tnadeau@cisco.com The PWE3 Working Group (email distribution pwe3@ietf.org, http://www.ietf.org/html.charters/pwe3-charter.html) " DESCRIPTION "This MIB module contains managed object definitions for Circuit Emulation over Packet (CEP) as in: Malis, A., Prayson, P., Cohen, R. and Zelig, D. 'SONET/SDH Circuit Emulation Over Packet (CEP)', RFC yyyy -- RFC Editor: Please replace yyyy with actual RFC number and -- remove this note Copyright (C) The Internet Society (2006). This version of this MIB module is part of RFC yyyy; see the RFC itself for full legal notices. -- RFC Editor: Please replace yyyy with actual RFC number and -- remove this note " -- Revision history. REVISION "200610171200Z" -- 17 October 2006 12:00:00 GMT DESCRIPTION "Initial version published as part of RFC XXXX." -- RFC Editor: Please replace XXXX with actual RFC number and remove -- this note ::= { transmission XXXX } -- To be assigned by IANA -- RFC Editor: Please replace the XXXX with the -- IANA assigned value and remove this note -- Local Textual conventions PwCepCfgIndex ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Index into the pwCepCfgTable." SYNTAX Unsigned32 (1..4294967295) PwCepSonetEbm ::= TEXTUAL-CONVENTION STATUS current Zelig, et al. Expires April 25, 2007 [Page 10] Internet-Draft PW CEP MIB October 2006 DESCRIPTION "Equipped Bit Mask (EBM) used for fractional STS-1/VC-3. The EBM bits are the 28 least significant bits out of the 32 bit value" SYNTAX Unsigned32 PwCepSdhVc4Ebm ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Equipped Bit Mask (EBM) used for each TUG-3 in fractional VC-4 circuits. The EBM bits are the 30 least significant bits out of the 32 bit value " SYNTAX Unsigned32 PwCepSonetVtgMap ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The VT/VC types carried in the 7 VTG/TUG-2s. The format is 28 bits in the form of an Equipped Bit Mask (EBM) for fractional STS-1/VC-3. The mapping specifies the maximal occupancies of VT/VC within each VTG/TUG-2. For example, all four bits are set to 1 in this objects it represents a VTG carrying VT1.5/VC11s, while only three are set when VT2/VC12 are carried within this VTG. The relevant bits are the 28 least significant bits out of the 32 bit value." SYNTAX Unsigned32 PwCepFracAsyncMap ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The type of Asynchronous mapping carried inside STS-1, VC-3 or TUG-3 containing TU-3 circuit. The value of 'other' MUST be used if the Use of this object is not applicable." SYNTAX INTEGER { other ( 1), ds3 ( 2), e3 ( 3) } -- Top level components of this MIB module. -- Tables, Scalars pwCepObjects OBJECT IDENTIFIER ::= { pwCepStdMIB 1 } -- Conformance pwCepConformance OBJECT IDENTIFIER Zelig, et al. Expires April 25, 2007 [Page 11] Internet-Draft PW CEP MIB October 2006 ::= { pwCepStdMIB 2 } -- CEP PW table pwCepTable OBJECT-TYPE SYNTAX SEQUENCE OF PwCepEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains objects and parameters for managing and monitoring the CEP PW." ::= { pwCepObjects 1 } pwCepEntry OBJECT-TYPE SYNTAX PwCepEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry represents the association of a SONET/SDH PATH or VT to a PW. This table is indexed by the pwIndex of the applicable PW entry in the pwTable. An entry is created in this table by the agent for every entry in the pwTable with a pwType of 'cep'." INDEX { pwIndex } ::= { pwCepTable 1 } PwCepEntry ::= SEQUENCE { pwCepType INTEGER, pwCepSonetIfIndex InterfaceIndexOrZero, pwCepSonetConfigErrorOrStatus BITS, pwCepCfgIndex PwCfgIndexOrzero, pwCepTimeElapsed HCPerfTimeElapsed, pwCepValidIntervals HCPerfValidIntervals, pwCepIndications BITS, pwCepLastEsTimeStamp TimeStamp, pwCepPeerCepOption Unsigned32 } pwCepType OBJECT-TYPE SYNTAX INTEGER { spe (1), vt (2), fracSpe (3) } Zelig, et al. Expires April 25, 2007 [Page 12] Internet-Draft PW CEP MIB October 2006 MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the sub-type of CEP PW. Currently only structured types are supported: 'spe'(1) : SONET STS-Nc signals. 'vt' (2) : SONET VT-x (x=1.5,2,3,6) signals. 'fracSpe' (3) : SONET fractional STS-1 or SDH fractional VC-3 or VC-4 carrying tributaries or Asynchronous signals. Support of 'vt' mode or 'fracSpe' mode is optional." DEFVAL { spe } ::= { pwCepEntry 1 } pwCepSonetIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-write STATUS current DESCRIPTION "This is a unique index within the ifTable. It represents the interface index for the SONET path for SPE emulation (RFC3593 section 3.3), an interface index for the SONET VT (RFC3593 section 3.4) if the VT to be emulated is extracted a SONET signal or locally mapped from a physical interface. A value of zero indicates an interface index that has yet to be determined. Once set, if the SONET ifIndex is (for some reason) later removed, the agent MAY delete the associated PW rows (e.g., this pwCepTableEntry). If the agent does not delete the rows, it is recommended that the agent set this object to zero." ::= { pwCepEntry 2 } pwCepSonetConfigErrorOrStatus OBJECT-TYPE SYNTAX BITS { other ( 0), timeslotInUse ( 1), timeslotMisuse ( 2), peerDbaIncompatible ( 3), -- Status Only peerEbmIncompatible ( 4), peerRtpIncompatible ( 5), peerAsyncIncompatible ( 6), Zelig, et al. Expires April 25, 2007 [Page 13] Internet-Draft PW CEP MIB October 2006 peerDbaAsymetric ( 7), -- Status Only peerEbmAsymetric ( 8), peerRtpAsymetric ( 9), peerAsyncAsymetric (10) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object reports a configuration mismatch inside the local node or between the local node and the peer node. Some bits indicate an error and some are simply status report thats does not affect the forwarding process. 'timeslotInUse'(1) is set when another CEP PW has already reserved a timeslot(s) that this CEP PW is attempting to reserved. 'timeslotMisuse'(2) is set when the stated timeslot this PW is trying to use is not legal. For example, if specifying a starting timeslot of 45 for a SONET path of an STS-12c width. The peerIncompatible bits are set if the local configuration is not compatible with the peer configuration as available from the CEP option received through the signaling process from the peer, and the the local node cannot support such asymetric configuration. The peerAsymetric bits are set if the local configuration is not compatible with the peer configuration as available from the CEP option received through the signaling process from the peer, however the local node can support such asymetric configuration. " REFERENCE "Malis, A., et al, 'SONET/SDH Circuit Emulation over Packet (CEP), RFC yyyy, section 11. " -- RFC Editor: Please replace yyyy with the RFC number and remove -- this remark ::= { pwCepEntry 3 } pwCepCfgIndex OBJECT-TYPE SYNTAX PwCfgIndexOrzero MAX-ACCESS read-write STATUS current DESCRIPTION "Index to CEP configuration table below. Multiple CEP PWs Zelig, et al. Expires April 25, 2007 [Page 14] Internet-Draft PW CEP MIB October 2006 MAY share a single pwCepCfgEntry." ::= { pwCepEntry 4 } pwCepTimeElapsed OBJECT-TYPE SYNTAX HCPerfTimeElapsed MAX-ACCESS read-only STATUS current DESCRIPTION "The number of seconds, including partial seconds, that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value." ::= { pwCepEntry 5 } pwCepValidIntervals OBJECT-TYPE SYNTAX HCPerfValidIntervals MAX-ACCESS read-only STATUS current DESCRIPTION "The number of previous 15-minute intervals for which data was collected. An agent with CEP capability must be capable of supporting at least n intervals. The minimum value of n is 4, the default of n is 32 and the maximum value of n is 96. " ::= { pwCepEntry 6 } pwCepIndications OBJECT-TYPE SYNTAX BITS { missingPkt ( 0), ooRngDropped( 1), jtrBfrUnder ( 2), pktMalformed( 3), lops ( 4), cepRdi ( 5), cepAis ( 6), badHdrStack ( 7), cepNeFailure( 8), cepFeFailure( 9) } MAX-ACCESS read-write STATUS current DESCRIPTION "Definitions: Zelig, et al. Expires April 25, 2007 [Page 15] Internet-Draft PW CEP MIB October 2006 'missingPkt'(0) - While playing out a sequence of packets, a packet(s) was determined to be missing based on a gap in the CEP sequence number. Note: If the implementation supports packet re-ordering, detecting gaps should not take place as packets arrive, only as they are played out - this gives time for mis-ordered packets to arrive late. 'ooRngDropped'(1) - Packet(s) arrives that is outside the range of the jitter buffer. This may be because the jitter buffer is full, or the sequence number addresses a buffer outside the current jitter buffer range, or addresses an already occupied buffer within range. Whether or not packet re-ordering is supported by the implementation, this indication MUST be supported. 'jtrBfrUnder'(2) - The jitter buffer underflowed due to not enough packets arriving as packets were being played out. 'pktMalformed'(3) - Any error related to unexpected packet format (except bad header stack) or unexpcted length. 'lops'(4) - Loss Of Packet Synchronization. 'cepRdi'(5) - Circuit Emulation over Packet Remote Defect Indication. Generated by the remote CEP de-packetizer when detecting LOPS. Note: Mot generated by the remote SONET function. See draft-ietf-pwe3-sonet. 'cepAis'(6) - Remote CEP packetizer has detected AIS on its incoming SONET stream. Note: cepAis MUST NOT (in itself) cause a CEP down notification. 'badHdrStack'(7) - This indication is set when the number of CEP header extensions detected in incoming packets does not match the expected number. 'cepNeFailure'(8) - Set when CEP-NE failure is currenly declared. 'cepFeFailure'(8) - Set when CEP-FE failure is currenly declared. This object MUST hold the accumulated indications, until the next SNMP write that clear the indication(s). Writing a non zero value MUST fail. Zelig, et al. Expires April 25, 2007 [Page 16] Internet-Draft PW CEP MIB October 2006 Currently there is no hierarchy of CEP defects. The algorithm used to capture these indications is implementation specific." ::= { pwCepEntry 7 } pwCepLastEsTimeStamp OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime on the most recent occasion at which the CEP PW entered the ES or SES state." ::= { pwCepEntry 8 } pwCepPeerCepOption OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of CEP option parameter as received from the peer by the PW signaling protocol." ::= { pwCepEntry 9 } -- End of CEP PW table -- Obtain index for PW CEP Configuration table entries pwCepCfgIndexNext OBJECT-TYPE SYNTAX PwCfgIndexOrzero MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains an appropriate value to be used for pwCepCfgIndex when creating entries in the pwCepCfgTable. The value 0 indicates that no unassigned entries are available. To obtain the value of pwCepCfgIndex for a new entry in the pwCepCfgTable, the manager issues a management protocol retrieval operation to obtain the current value of pwCepCfgIndex. After each retrieval operation, the agent should modify the value to reflect the next unassigned index. After a manager retrieves a value the agent will determine through its local policy when this index value will be made Zelig, et al. Expires April 25, 2007 [Page 17] Internet-Draft PW CEP MIB October 2006 available for reuse." ::= { pwCepObjects 2 } -- PW CEP PW Configuration Table pwCepCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF PwCepCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains a set of parameters that may be referenced by one or more CEP PWs by pwCepTable." ::= { pwCepObjects 3 } pwCepCfgEntry OBJECT-TYPE SYNTAX PwCepCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "These parameters define the characteristics of a CEP PW. They are grouped here to ease NMS burden. Once an entry is created here it may be re-used by many PWs." INDEX { pwCepCfgTableIndex } ::= { pwCepCfgTable 1 } PwCepCfgEntry ::= SEQUENCE { pwCepCfgTableIndex PwCepCfgIndex, pwCepConfigError BITS, pwCepSonetPayloadLength Unsigned32, pwCepCfgMinPktLength Unsigned32, pwCepCfgPktReorder TruthValue, pwCepCfgEnableDBA BITS, pwCepCfgRtpHdrSuppress TruthValue, pwCepCfgJtrBfrDepth Unsigned32, pwCepCfgConsecPktsInsync Unsigned32, pwCepCfgConsecMissingOutSync Unsigned32, pwCepCfgPktErrorPlayOutValue Unsigned32, pwCepCfgMissingPktsToSes Unsigned32, Zelig, et al. Expires April 25, 2007 [Page 18] Internet-Draft PW CEP MIB October 2006 pwCepCfgSesToUas Unsigned32, pwCepCfgSecsToExitUas Unsigned32, pwCepCfgName SnmpAdminString, pwCepCfgRowStatus RowStatus, pwCepCfgStorageType StorageType } pwCepCfgTableIndex OBJECT-TYPE SYNTAX PwCepCfgIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Primary index to this table." ::= { pwCepCfgEntry 1 } pwCepConfigError OBJECT-TYPE SYNTAX BITS { other ( 0), dba ( 1), lopsPktCount ( 2), pktLength ( 3), jtrBfrDepth ( 4), rtpHdrSetting ( 5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Various configurations errors, detected when a configured value within the pwCepCfg or pwCepSonetExt tables cannot be supported by the local agent." ::= { pwCepCfgEntry 2 } pwCepSonetPayloadLength OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "The number of SONET bytes of the Path or VT carried as payload within one packet. For example, for STS-1/VC-3 SPE circuits, value of 783 bytes indicates that each packet carries payload equivalent to one frame. For VT1.5/VC11 circuits, a payload length of 104 bytes indicates that each packet carries payload equivalent to one VT1.5 super-frame. The actual payload size may be different, due to bandwidth Zelig, et al. Expires April 25, 2007 [Page 19] Internet-Draft PW CEP MIB October 2006 reduction modes, e.g. DBA mode or dynamically assigned fractional SPE. This length applies to inbound and outbound packets carrying user payload. Although there is no control over inbound packets, those of illegal length are discarded and accounted for (see pwCepPerf...Malformed.) The default values are determined by the pwCepType: 783 for pwCepType equal spe(2) or fracSpe(3). For vt(3) modes, the applicable super-frame payload size is the default value. " REFERENCE "Malis, A., et al, 'SONET/SDH Circuit Emulation over Packet (CEP), RFC yyyy, sections 4.1 and 10.2" -- RFC Editor: Please replace yyyy with the RFC number and remove -- this remark ::= { pwCepCfgEntry 3 } pwCepCfgMinPktLength OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "This is the minimum CEP packet length in number of bytes (including CEP header and payload). It applies to CEP's bandwidth-savings packets. Currently DBA is the only bandwidth-savings packet type (in the future, CEP may support compression). Minimum packet length is necessary in some systems or networks. Setting Zero here indicates that there is no minimum packet restriction." DEFVAL { 0 } ::= { pwCepCfgEntry 4 } pwCepCfgPktReorder OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "If set 'true' - as inbound packets are queued in the jitter buffer, out of order packets are re-ordered. The maximum sequence number differential (i.e., the range in which re-sequencing can occur) is dependant on the depth Zelig, et al. Expires April 25, 2007 [Page 20] Internet-Draft PW CEP MIB October 2006 of the jitter buffer. If the local agent support packet re-ordering, the default value SHOULD be set to 'true', otherwise, this value SHOULD be set to 'false'." ::= { pwCepCfgEntry 5 } pwCepCfgEnableDBA OBJECT-TYPE SYNTAX BITS { ais (0), unequipped (1) } MAX-ACCESS read-create STATUS current DESCRIPTION "Bits set here MUST enable the DBA (dynamic bandwidth allocation) feature for the specified condition. Setting 'ais' MUST cause CEP packet payload suppression when AIS is detected on the associated SONET path. Similarly, 'unequipped' MUST cause payload suppression when an un-equipped condition is detected on the SONET/SDH PATH/VT. During these conditions, CEP packets will continue to be sent, but with indicators set in the CEP header instructing the remote to play all ones (for AIS) or all zeros (for un-equipped) onto its SONET path. NOTE: Some implementations may not support this feature. In these cases, this object should be read-only." REFERENCE "Malis, A., et al, 'SONET/SDH Circuit Emulation over Packet (CEP), RFC yyyy, section 10. " -- RFC Editor: Please replace yyyy with the RFC number and remove -- this remark ::= { pwCepCfgEntry 6 } pwCepCfgRtpHdrSuppress OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "If set True, an RTP header is not pre-pended to the CEP packet." REFERENCE "Malis, A., et al, 'SONET/SDH Circuit Emulation over Packet Zelig, et al. Expires April 25, 2007 [Page 21] Internet-Draft PW CEP MIB October 2006 (CEP), RFC yyyy, section 4.3. " -- RFC Editor: Please replace yyyy with the RFC number and remove -- this remark DEFVAL { false } ::= { pwCepCfgEntry 7 } pwCepCfgJtrBfrDepth OBJECT-TYPE SYNTAX Unsigned32 UNITS "micro-seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "This setting configures the number of microseconds of expected packet delay variation for this CEP PW over the PSN. The actual jitter buffer MUST be at least twice this value for proper operation, and is implementation specific. If configured to a value not supported by the implementation, the agent MUST return an error code 'jtrBfrDepth' in 'pwCepConfigError'." ::= { pwCepCfgEntry 8 } -- -- The following counters work together to integrate (filter) -- errors and the lack of errors on the CEP PW. An error is -- caused by a missing packet. Missing packet can be a result -- of packet loss in the network, (uncorrectable) packet out -- of sequence, packet length error, jitter buffer overflow, -- and jitter buffer underflow. The result declares whether -- or not the CEP PW is in Loss of Packet Sync (LOPS) state. -- pwCepCfgConsecPktsInsync OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "Consecutive pkts with sequential sequence numbers required to exit the LOPS state." REFERENCE "Malis, A., et al, 'SONET/SDH Circuit Emulation over Packet (CEP), RFC yyyy, section 5.2.2. " -- RFC Editor: Please replace yyyy with the RFC number and remove Zelig, et al. Expires April 25, 2007 [Page 22] Internet-Draft PW CEP MIB October 2006 -- this remark DEFVAL { 2 } ::= { pwCepCfgEntry 9 } pwCepCfgConsecMissingOutSync OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "Consecutive missing pkts required to enter the LOPS state." REFERENCE "Malis, A., et al, 'SONET/SDH Circuit Emulation over Packet (CEP), RFC yyyy, section 5.2.2. " -- RFC Editor: Please replace yyyy with the RFC number and remove -- this remark DEFVAL { 10 } ::= { pwCepCfgEntry 10 } pwCepCfgPktErrorPlayOutValue OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "This is the value played when inbound packets have over/underflowed the jitter buffer, or are missing for any reason. This byte pattern is sent (played) on the SONET path." DEFVAL { 255 } -- Play all ones, equal to AIS indications. ::= { pwCepCfgEntry 11 } pwCepCfgMissingPktsToSes OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Number of missing packets detected (consecutive or not) within a 1 second window to cause a Severely Errored Second (SES) to be counted." REFERENCE "Malis, A., et al, 'SONET/SDH Circuit Emulation over Packet (CEP), RFC yyyy, section 9.1. " -- RFC Editor: Please replace yyyy with the RFC number and remove Zelig, et al. Expires April 25, 2007 [Page 23] Internet-Draft PW CEP MIB October 2006 -- this remark DEFVAL { 3 } ::= { pwCepCfgEntry 12 } pwCepCfgSesToUas OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Number of consecutive SESs before declaring PW in UAS state (and at which point pwCepPerfUASs starts counting). The SesToUas default value is 10 seconds. NOTE: Similar to RFC 3592, If the agent chooses to update the various performance statistics in real time then it must be prepared to retroactively reduce the ES, SES, counts by this value and increase the UAS count by this value when it determines that UAS state has been entered. NOTE: See pwCepPerfSESs and pwCepPerfUASs." REFERENCE "Malis, A., et al, 'SONET/SDH Circuit Emulation over Packet (CEP), RFC yyyy, section 9.1. " -- RFC Editor: Please replace yyyy with the RFC number and remove -- this remark DEFVAL { 10 } ::= { pwCepCfgEntry 13 } pwCepCfgSecsToExitUas OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Number of consecutive nonSESs before declaring PW is NOT in UAS state (and at which point pwCepPerfUASs stops counting)." REFERENCE "Malis, A., et al, 'SONET/SDH Circuit Emulation over Packet (CEP), RFC yyyy, section 9.1. " -- RFC Editor: Please replace yyyy with the RFC number and remove -- this remark DEFVAL { 10 } ::= { pwCepCfgEntry 14 } Zelig, et al. Expires April 25, 2007 [Page 24] Internet-Draft PW CEP MIB October 2006 pwCepCfgName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "This variable contains the name of the Configuration entry. This name may be used to help the NMS to display the purpose of the entry." ::= { pwCepCfgEntry 15 } pwCepCfgRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "For creating, modifying, and deleting this row. None of the read-create objects values can be changed when pwCepCfgRowStatus is in the active(1) state. Changes are allowed when the pwRowStatus is in notInService(2) or notReady(3) states only. If the operator need to change one of the values for an active row (for example in order to fix a mismatch in configuration between the local node and the peer), the pwCepCfgRowStatus should be first changed to notInService(2), the objects may be changed now, and later to active(1) in order to re-initiate the signaling process with the new values in effect. Change of status from the active(1) state or deleting a row SHOULD be blocked by the local agent if the row is referenced by any pwCepEntry those pwRowStatus is in the active(1) state." ::= { pwCepCfgEntry 16 } pwCepCfgStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "This variable indicates the storage type for this row." ::= { pwCepCfgEntry 17 } -- End of CEP PW Configuration Parameter Table Zelig, et al. Expires April 25, 2007 [Page 25] Internet-Draft PW CEP MIB October 2006 -- Fractional CEP Configuration Table pwCepFracTable OBJECT-TYPE SYNTAX SEQUENCE OF PwCepFracEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains a set of parameters for CEP PWs with pwCepType FRAC type." ::= { pwCepObjects 4 } pwCepFracEntry OBJECT-TYPE SYNTAX PwCepFracEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of this table can be created in two options: - By the EMS in advance for creating the PW. - By the agent automatically when the PW is set up. The first option is typically used when there is an NSP cross-connect option between the physical ports and the emulated (virtual ports), while the second MAY be used when there is a one-to-one mapping between the emulated signal and the physical signal. " INDEX { pwCepFracIndex } ::= { pwCepFracTable 1 } PwCepFracEntry ::= SEQUENCE { pwCepFracIndex InterfaceIndex, pwCepFracMode INTEGER, pwCepFracConfigError BITS, pwCepFracAsync PwCepFracAsyncMap, pwCepFracVtgMap PwCepSonetVtgMap, pwCepFracEbm PwCepSonetEbm, pwCepFracPeerEbm PwCepSonetEbm, pwCepFracSdhVc4Mode INTEGER, pwCepFracSdhVc4Tu3Map1 PwCepFracAsyncMap, pwCepFracSdhVc4Tu3Map2 PwCepFracAsyncMap, pwCepFracSdhVc4Tu3Map3 PwCepFracAsyncMap, pwCepFracSdhVc4Tug2Map1 PwCepSonetVtgMap, pwCepFracSdhVc4Tug2Map2 PwCepSonetVtgMap, pwCepFracSdhVc4Tug2Map3 PwCepSonetVtgMap, pwCepFracSdhVc4Ebm1 PwCepSdhVc4Ebm, pwCepFracSdhVc4Ebm2 PwCepSdhVc4Ebm, Zelig, et al. Expires April 25, 2007 [Page 26] Internet-Draft PW CEP MIB October 2006 pwCepFracSdhVc4Ebm3 PwCepSdhVc4Ebm, pwCepFracSdhVc4PeerEbm1 PwCepSdhVc4Ebm, pwCepFracSdhVc4PeerEbm2 PwCepSdhVc4Ebm, pwCepFracSdhVc4PeerEbm3 PwCepSdhVc4Ebm, pwCepFracRowStatus RowStatus, pwCepFracStorageType StorageType } pwCepFracIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is the primary index of this table. It is a unique index within the ifTable. It represents the interface index for the SONET path (RFC 3592 section 3.3) for fractional SPE emulation. It may represent an internal (virtual) interface if an NSP function exists between the physical interface and the emulation process." ::= { pwCepFracEntry 1 } pwCepFracMode OBJECT-TYPE SYNTAX INTEGER { notApplicable ( 1), dynamic ( 2), static ( 3), staticWithEbm ( 4), staticAsync ( 5) } MAX-ACCESS read-create STATUS current DESCRIPTION "Fractional mode for STS-1/VC-3 or VC-4 circuits: notApplicable - When this object is not applicable. dynamic - EBM carried within the CEP header. Unequipped VTs are removed from the payload on the fly. static - EBM not carried within the CEP header. Only VTs defined in the EBM are carried within the payload. staticWithEbm - EBM carried within the CEP header. Only VTs defined in the EBM are carried within the payload. staticAsync - Asynchronous E3/T3 fixed byte removal only. " DEFVAL { dynamic } Zelig, et al. Expires April 25, 2007 [Page 27] Internet-Draft PW CEP MIB October 2006 ::= { pwCepFracEntry 2 } pwCepFracConfigError OBJECT-TYPE SYNTAX BITS { other ( 0), vtgMapEbmConflict ( 1), vtgMapAsyncConflict ( 2) } MAX-ACCESS read-only STATUS current DESCRIPTION "vtgMapEbmConflict is set when the configured static EBM does not match the configured vtgMap for fractional STS-1/VC-3 circuits, or when the TUG2Map is in conflict with the static EBM for VC-4 circuits. For example, if the vtgMap specifies that VTG#1 carries VT2 VTs while the EBM indicate that four VTs are equipped within VTG#1. vtgMapAsyncConflict is set when there is a conflict between the mode, the async indication and the vtgMap fields. For example, fractional mode is set to Static Async while the VtgMap indicate that the STS-1/VC-3 carries VTs, or in fractional VC-4 circuits where both async1 and Tug2Map are set." ::= { pwCepFracEntry 3 } pwCepFracAsync OBJECT-TYPE SYNTAX PwCepFracAsyncMap MAX-ACCESS read-create STATUS current DESCRIPTION "The Asynchronous payload carried within the STS-1/VC-3. This variable should be set when 'staticAsync' Fractional STS-1/VC-3 pwCepFracMode is selected, and hold the value of 'other' otherwise." DEFVAL { other } ::= { pwCepFracEntry 4 } pwCepFracVtgMap OBJECT-TYPE SYNTAX PwCepSonetVtgMap MAX-ACCESS read-create STATUS current DESCRIPTION "The VT/VC types of the seven VTG/TUG-2 within the STS-1/VC-3. This variable should be set when 'dynamic', 'static' Zelig, et al. Expires April 25, 2007 [Page 28] Internet-Draft PW CEP MIB October 2006 or 'staticWithEbm' Fractional STS-1/VC-3 pwCepFracMode is selected. " ::= { pwCepFracEntry 5 } pwCepFracEbm OBJECT-TYPE SYNTAX PwCepSonetEbm MAX-ACCESS read-create STATUS current DESCRIPTION "Static Equipped Bit Mask (EBM) for STS-1/VC-3 channel. This variable MAY be set when 'static' or 'staticWithEbm' Fractional STS-1/VC-3 pwCepFracMode is selected. It is possible that the EBM that would be used is available based on configuration of other MIB modules. In these cases this object is read-only and reflects the actual EBM that would be used." ::= { pwCepFracEntry 6 } pwCepFracPeerEbm OBJECT-TYPE SYNTAX PwCepSonetEbm MAX-ACCESS read-only STATUS current DESCRIPTION "Equipped Bit Mask (EBM) for STS-1/VC-3 channel received from the peer within the CEP extension header." ::= { pwCepFracEntry 7 } pwCepFracSdhVc4Mode OBJECT-TYPE SYNTAX INTEGER { notApplicable ( 1), dynamic ( 2), static ( 3), staticWithEbm ( 4) } MAX-ACCESS read-create STATUS current DESCRIPTION "Fractional mode for VC-4 circuits: notApllicable - When this is not VC-4 circuit. dynamic - EBM carried within the CEP header. Unequipped VTs are removed from the payload on the fly. Zelig, et al. Expires April 25, 2007 [Page 29] Internet-Draft PW CEP MIB October 2006 static - EBM not carried within the CEP header. Only VTs defined in the EBM are carried within the payload. staticWithEbm - EBM carried within the CEP header. Only VTs defined in the EBM are carried within the payload. " DEFVAL { notApplicable } ::= { pwCepFracEntry 8 } pwCepFracSdhVc4Tu3Map1 OBJECT-TYPE SYNTAX PwCepFracAsyncMap MAX-ACCESS read-create STATUS current DESCRIPTION "If the first TUG-3 within the VC-4 contains a TU-3, this variable must be set to the required mode. " DEFVAL { other } ::= { pwCepFracEntry 9 } pwCepFracSdhVc4Tu3Map2 OBJECT-TYPE SYNTAX PwCepFracAsyncMap MAX-ACCESS read-create STATUS current DESCRIPTION "If the second TUG-3 within the VC-4 contains a TU-3, this variable must be set." DEFVAL { other } ::= { pwCepFracEntry 10 } pwCepFracSdhVc4Tu3Map3 OBJECT-TYPE SYNTAX PwCepFracAsyncMap MAX-ACCESS read-create STATUS current DESCRIPTION "If the third TUG-3 within the VC-4 contains a TU-3, this variable must be set. " DEFVAL { other } ::= { pwCepFracEntry 11 } pwCepFracSdhVc4Tug2Map1 OBJECT-TYPE Zelig, et al. Expires April 25, 2007 [Page 30] Internet-Draft PW CEP MIB October 2006 SYNTAX PwCepSonetVtgMap MAX-ACCESS read-create STATUS current DESCRIPTION "The VC types of the seven TUG-2 within the first TUG-3 of the VC-4. " ::= { pwCepFracEntry 12 } pwCepFracSdhVc4Tug2Map2 OBJECT-TYPE SYNTAX PwCepSonetVtgMap MAX-ACCESS read-create STATUS current DESCRIPTION "The VC types of the seven TUG-2 within the second TUG-3 of the VC-4. " ::= { pwCepFracEntry 13 } pwCepFracSdhVc4Tug2Map3 OBJECT-TYPE SYNTAX PwCepSonetVtgMap MAX-ACCESS read-create STATUS current DESCRIPTION "The VC types of the seven TUG-2 within the third TUG-3 of the VC-4. " ::= { pwCepFracEntry 14 } pwCepFracSdhVc4Ebm1 OBJECT-TYPE SYNTAX PwCepSdhVc4Ebm MAX-ACCESS read-create STATUS current DESCRIPTION "Static Equipped Bit Mask (EBM) for first TUG-3 within the VC-4. This variable should be set when 'static' or 'staticWithEbm' Fractional VC-4 pwCepFracMode is selected. It is possible that the EBM that would be used is available based on configuration of other MIB modules. In these cases this object is read-only and reflects the actual EBM that would be used." ::= { pwCepFracEntry 15 } pwCepFracSdhVc4Ebm2 OBJECT-TYPE SYNTAX PwCepSdhVc4Ebm Zelig, et al. Expires April 25, 2007 [Page 31] Internet-Draft PW CEP MIB October 2006 MAX-ACCESS read-create STATUS current DESCRIPTION "Static Equipped Bit Mask (EBM) for second TUG-3 within the VC-4. This variable should be set when 'static' or 'StaticWithEbm' Fractional VC-4 pwCepFracMode is selected. It is possible that the EBM that would be used is available based on configuration of other MIB modules. In these cases this object is read-only and reflects the actual EBM that would be used." ::= { pwCepFracEntry 16 } pwCepFracSdhVc4Ebm3 OBJECT-TYPE SYNTAX PwCepSdhVc4Ebm MAX-ACCESS read-create STATUS current DESCRIPTION "Static Equipped Bit Mask (EBM) for third TUG-3 within the VC-4. This variable should be set when 'Static' or 'staticWithEbm' Fractional VC-4 pwCepFracMode is selected. It is possible that the EBM that would be used is available based on configuration of other MIB modules. In these cases this object is read-only and reflects the actual EBM that would be used." ::= { pwCepFracEntry 17 } pwCepFracSdhVc4PeerEbm1 OBJECT-TYPE SYNTAX PwCepSdhVc4Ebm MAX-ACCESS read-only STATUS current DESCRIPTION "Equipped Bit Mask (EBM) for the first TUG-3 within the fractional VC-4 channel received from peer within the CEP extension header." ::= { pwCepFracEntry 18 } pwCepFracSdhVc4PeerEbm2 OBJECT-TYPE SYNTAX PwCepSdhVc4Ebm MAX-ACCESS read-only STATUS current DESCRIPTION Zelig, et al. Expires April 25, 2007 [Page 32] Internet-Draft PW CEP MIB October 2006 "Equipped Bit Mask (EBM) for the second TUG-3 within the fractional VC-4 channel received from peer within the CEP extension header." ::= { pwCepFracEntry 19 } pwCepFracSdhVc4PeerEbm3 OBJECT-TYPE SYNTAX PwCepSdhVc4Ebm MAX-ACCESS read-only STATUS current DESCRIPTION "Equipped Bit Mask (EBM) for the third TUG-3 within the fractional VC-4 channel received from peer within the CEP extension header." ::= { pwCepFracEntry 20 } pwCepFracRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "For creating, modifying, and deleting this row. It is allowed to make changes to read-create entries in this table, but the operator should be aware that such changes for an active row may cause temporary mis-configurations between the peers in terms of the carried signal, leading to traffic disruption." ::= { pwCepFracEntry 21 } pwCepFracStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "This variable indicates the storage type for this object." ::= { pwCepFracEntry 22 } -- End Fractional CEP Configuration Table -- CEP PW Performance Current Interval Table. pwCepPerfCurrentTable OBJECT-TYPE Zelig, et al. Expires April 25, 2007 [Page 33] Internet-Draft PW CEP MIB October 2006 SYNTAX SEQUENCE OF PwCepPerfCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "CEP bridges the SONET and packet worlds. In the packet world, counts typically start from the time of service creation - and don't stop. In the SONET world, counts are kept in 15-minute intervals. The PW CEP MIB supports both methods. The current 15-minute interval counts are in this table. The interval and total stats are in tables following this. This table provides per CEP PW performance information. HC (high capacity) counters are required for some counts due to the high speeds expected with CEP services. A SONET path of width 48 (STS-48c) can rollover non-HC counters in a few minutes." ::= { pwCepObjects 5 } pwCepPerfCurrentEntry OBJECT-TYPE SYNTAX PwCepPerfCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created by the agent for every pwCep entry. After 15 minutes, the contents of this table entry are copied to a new entry in the pwCepPerfInterval table and the counts in this entry are reset to zero." INDEX { pwIndex } ::= { pwCepPerfCurrentTable 1 } PwCepPerfCurrentEntry ::= SEQUENCE { pwCepPerfCurrentDbaInPacketsHC HCPerfCurrentCount, pwCepPerfCurrentDbaOutPacketsHC HCPerfCurrentCount, pwCepPerfCurrentInNegPtrAdjust PerfCurrentCount, pwCepPerfCurrentInPosPtrAdjust PerfCurrentCount, pwCepPerfCurrentInPtrAdjustSecs PerfCurrentCount, pwCepPerfCurrentOutNegPtrAdjust PerfCurrentCount, pwCepPerfCurrentOutPosPtrAdjust PerfCurrentCount, pwCepPerfCurrentOutPtrAdjustSecs PerfCurrentCount, pwCepPerfCurrentAbsPtrAdjust Integer32, pwCepPerfCurrentMissingPkts PerfCurrentCount, pwCepPerfCurrentPktsOoseq PerfCurrentCount, Zelig, et al. Expires April 25, 2007 [Page 34] Internet-Draft PW CEP MIB October 2006 pwCepPerfCurrentPktsOoRngDropped PerfCurrentCount, pwCepPerfCurrentJtrBfrUnderruns PerfCurrentCount, pwCepPerfCurrentPktsMalformed PerfCurrentCount, pwCepPerfCurrentSummaryErrors PerfCurrentCount, pwCepPerfCurrentESs PerfCurrentCount, pwCepPerfCurrentSESs PerfCurrentCount, pwCepPerfCurrentUASs PerfCurrentCount, pwCepPerfCurrentFC PerfCurrentCount } pwCepPerfCurrentDbaInPacketsHC OBJECT-TYPE SYNTAX HCPerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of DBA packets received." ::= { pwCepPerfCurrentEntry 1 } pwCepPerfCurrentDbaOutPacketsHC OBJECT-TYPE SYNTAX HCPerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of DBA packets sent." ::= { pwCepPerfCurrentEntry 2 } -- Pointer adjustment stats pwCepPerfCurrentInNegPtrAdjust OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of negative pointer adjustments sent on the SONET path based on CEP pointer adjustments received." ::= { pwCepPerfCurrentEntry 3 } pwCepPerfCurrentInPosPtrAdjust OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of positive pointer adjustments sent on the SONET path based on CEP pointer adjustments received." ::= { pwCepPerfCurrentEntry 4 } Zelig, et al. Expires April 25, 2007 [Page 35] Internet-Draft PW CEP MIB October 2006 pwCepPerfCurrentInPtrAdjustSecs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds in which a positive or negative pointer adjustment was sent on the SONET path." ::= { pwCepPerfCurrentEntry 5 } pwCepPerfCurrentOutNegPtrAdjust OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of negative pointer adjustments seen on the SONET path and encoded onto sent CEP packets." ::= { pwCepPerfCurrentEntry 6 } pwCepPerfCurrentOutPosPtrAdjust OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of positive pointer adjustments seen on the SONET path and encoded onto sent CEP packets." ::= { pwCepPerfCurrentEntry 7 } pwCepPerfCurrentOutPtrAdjustSecs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds in which a positive or negative pointer adjustment was seen on the SONET path." ::= { pwCepPerfCurrentEntry 8 } pwCepPerfCurrentAbsPtrAdjust OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Absolute Pointer adjustments is relative adjustment drifts between inbound and outbound streams. It is calculated as absolute value of : ( InPosPtrAdjust - InNegPtrAdjust ) - (OutPosPtrAdjust - OutNegPtrAdjust) " ::= { pwCepPerfCurrentEntry 9 } Zelig, et al. Expires April 25, 2007 [Page 36] Internet-Draft PW CEP MIB October 2006 pwCepPerfCurrentMissingPkts OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of missing packets (as detected via CEP header sequence number gaps)." ::= { pwCepPerfCurrentEntry 10 } pwCepPerfCurrentPktsOoseq OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of sequence (via CEP header sequence numbers), but successfully re-ordered. Note: Some implementations may not support this feature (see pwCepCfgPktReorder)." ::= { pwCepPerfCurrentEntry 11 } pwCepPerfCurrentPktsOoRngDropped OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of range (via CEP header sequence numbers), and could not be re-ordered, or could not fit in the jitter buffer." ::= { pwCepPerfCurrentEntry 12 } pwCepPerfCurrentJtrBfrUnderruns OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times a packet needed to be played out and the jitter buffer was empty." ::= { pwCepPerfCurrentEntry 13 } pwCepPerfCurrentPktsMalformed OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected with unexpected size, or bad headers stack." ::= { pwCepPerfCurrentEntry 14 } Zelig, et al. Expires April 25, 2007 [Page 37] Internet-Draft PW CEP MIB October 2006 pwCepPerfCurrentSummaryErrors OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "A summary of all the packet error types above (from missing packets to bad length packets)." ::= { pwCepPerfCurrentEntry 15 } pwCepPerfCurrentESs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Errored Seconds encountered." ::= { pwCepPerfCurrentEntry 16 } pwCepPerfCurrentSESs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Severely Errored Seconds encountered." ::= { pwCepPerfCurrentEntry 17 } pwCepPerfCurrentUASs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Unavailable Seconds encountered." ::= { pwCepPerfCurrentEntry 18 } pwCepPerfCurrentFC OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "CEP Failure Counts (FC-CEP). The number of CEP failure events. A failure event begins when the LOPS failure is declared, and ends when the failure is cleared. A failure event that begins in one period and ends in another period is counted only in the period in which it begins." ::= { pwCepPerfCurrentEntry 19 } Zelig, et al. Expires April 25, 2007 [Page 38] Internet-Draft PW CEP MIB October 2006 -- End CEP PW Performance Current Interval Table -- CEP PW Performance 15-Minutes Interval Table. pwCepPerfIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF PwCepPerfIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides per CEP PW performance information much like the pwCepPerfCurrentTable above. However, these counts represent historical 15-minute intervals. Typically, this table will have a maximum of 96 entries for a 24 hour period, but is not limited to this. NOTE: Counter64 objects are used here, Counter32 is too small for OC-768 CEP PWs." ::= { pwCepObjects 6 } pwCepPerfIntervalEntry OBJECT-TYPE SYNTAX PwCepPerfIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created by the agent for every pwCepPerfCurrentEntry that is 15 minutes old. The contents of the Current entry are copied to the new entry here. The Current entry, then resets its counts to zero for the next current 15-minute interval. pwCepIndex is found in the pwCepCfg table." INDEX { pwIndex, pwCepPerfIntervalNumber } ::= { pwCepPerfIntervalTable 1 } PwCepPerfIntervalEntry ::= SEQUENCE { pwCepPerfIntervalNumber Integer32, pwCepPerfIntervalValidData TruthValue, pwCepPerfIntervalReset INTEGER, pwCepPerfIntervalTimeElapsed HCPerfTimeElapsed, pwCepPerfIntervalDbaInPacketsHC HCPerfIntervalCount, pwCepPerfIntervalDbaOutPacketsHC HCPerfIntervalCount, pwCepPerfIntervalInNegPtrAdjust PerfIntervalCount, pwCepPerfIntervalInPosPtrAdjust PerfIntervalCount, pwCepPerfIntervalInPtrAdjustSecs PerfIntervalCount, Zelig, et al. Expires April 25, 2007 [Page 39] Internet-Draft PW CEP MIB October 2006 pwCepPerfIntervalOutNegPtrAdjust PerfIntervalCount, pwCepPerfIntervalOutPosPtrAdjust PerfIntervalCount, pwCepPerfIntervalOutPtrAdjustSecs PerfIntervalCount, pwCepPerfIntervalAbsPtrAdjust Integer32, pwCepPerfIntervalMissingPkts PerfIntervalCount, pwCepPerfIntervalPktsOoseq PerfIntervalCount, pwCepPerfIntervalPktsOoRngDropped PerfIntervalCount, pwCepPerfIntervalJtrBfrUnderruns PerfIntervalCount, pwCepPerfIntervalPktsMalformed PerfIntervalCount, pwCepPerfIntervalSummaryErrors PerfIntervalCount, pwCepPerfIntervalESs PerfIntervalCount, pwCepPerfIntervalSESs PerfIntervalCount, pwCepPerfIntervalUASs PerfIntervalCount, pwCepPerfIntervalFC PerfIntervalCount } pwCepPerfIntervalNumber OBJECT-TYPE SYNTAX Integer32 (1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number (normally between 1 and 96 to cover a 24 hour period) which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15-minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. The minimum range of N is 1 through 4. The default range is 1 through 32. The maximum value of N is 1 through 96." ::= { pwCepPerfIntervalEntry 1 } pwCepPerfIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { pwCepPerfIntervalEntry 2 } pwCepPerfIntervalReset OBJECT-TYPE SYNTAX INTEGER { reset (1), normal(2) } Zelig, et al. Expires April 25, 2007 [Page 40] Internet-Draft PW CEP MIB October 2006 MAX-ACCESS read-create STATUS current DESCRIPTION "Used in cases where the user knows that the errors within this interval should not be counted. Writing 'reset' sets all error counts to zero." ::= { pwCepPerfIntervalEntry 3 } pwCepPerfIntervalTimeElapsed OBJECT-TYPE SYNTAX HCPerfTimeElapsed MAX-ACCESS read-only STATUS current DESCRIPTION "The duration of a particular interval in seconds, Adjustments in the system's time-of-day clock may cause the interval to be greater or less than, the normal value. Therefore this actual interval value is provided." ::= { pwCepPerfIntervalEntry 4 } pwCepPerfIntervalDbaInPacketsHC OBJECT-TYPE SYNTAX HCPerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of DBA packets received." ::= { pwCepPerfIntervalEntry 5 } pwCepPerfIntervalDbaOutPacketsHC OBJECT-TYPE SYNTAX HCPerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of DBA packets sent." ::= { pwCepPerfIntervalEntry 6 } -- Pointer adjustment stats pwCepPerfIntervalInNegPtrAdjust OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of negative pointer adjustments sent on the SONET path based on CEP pointer adjustments received." ::= { pwCepPerfIntervalEntry 7 } Zelig, et al. Expires April 25, 2007 [Page 41] Internet-Draft PW CEP MIB October 2006 pwCepPerfIntervalInPosPtrAdjust OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of positive pointer adjustments sent on the SONET path based on CEP pointer adjustments received." ::= { pwCepPerfIntervalEntry 8 } pwCepPerfIntervalInPtrAdjustSecs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds in which a pos or neg pointer adjustment was sent on the SONET path." ::= { pwCepPerfIntervalEntry 9 } pwCepPerfIntervalOutNegPtrAdjust OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of negative pointer adjustments seen on the SONET path and encoded onto sent CEP packets." ::= { pwCepPerfIntervalEntry 10 } pwCepPerfIntervalOutPosPtrAdjust OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of positive pointer adjustments seen on the SONET path and encoded onto sent CEP packets." ::= { pwCepPerfIntervalEntry 11 } pwCepPerfIntervalOutPtrAdjustSecs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds in which a pos or neg pointer adjustment was seen on the SONET path." ::= { pwCepPerfIntervalEntry 12 } pwCepPerfIntervalAbsPtrAdjust OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only Zelig, et al. Expires April 25, 2007 [Page 42] Internet-Draft PW CEP MIB October 2006 STATUS current DESCRIPTION "Absolute Pointer adjustments is relative adjustment drifts between inbound and outbound streams. It is calculated as absolute value of : ( InPosPtrAdjust - InNegPtrAdjust) - (OutPosPtrAdjust - OutNegPtrAdjust) " ::= { pwCepPerfIntervalEntry 13 } pwCepPerfIntervalMissingPkts OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of missing packets (as detected via CEP header sequence number gaps)." ::= { pwCepPerfIntervalEntry 14 } pwCepPerfIntervalPktsOoseq OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of sequence (via CEP header sequence numbers), but successfully re-ordered. Note: Some implementations mat not support this feature (see pwCepCfgPktReorder)." ::= { pwCepPerfIntervalEntry 15 } pwCepPerfIntervalPktsOoRngDropped OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of range (via CEP header sequence numbers), and could not be re- ordered, or could not fit in the jitter buffer." ::= { pwCepPerfIntervalEntry 16 } pwCepPerfIntervalJtrBfrUnderruns OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times a packet needed to be played out and the jitter buffer was empty." ::= { pwCepPerfIntervalEntry 17 } Zelig, et al. Expires April 25, 2007 [Page 43] Internet-Draft PW CEP MIB October 2006 pwCepPerfIntervalPktsMalformed OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected with unexpected size, or bad headers stack." ::= { pwCepPerfIntervalEntry 18 } pwCepPerfIntervalSummaryErrors OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "A summary of all the packet error types above (from missing packets to bad length packets)." ::= { pwCepPerfIntervalEntry 19 } pwCepPerfIntervalESs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Errored Seconds encountered." ::= { pwCepPerfIntervalEntry 20 } pwCepPerfIntervalSESs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Severely Errored Seconds encountered." ::= { pwCepPerfIntervalEntry 21 } pwCepPerfIntervalUASs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Unavailable Seconds encountered." ::= { pwCepPerfIntervalEntry 22 } pwCepPerfIntervalFC OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only Zelig, et al. Expires April 25, 2007 [Page 44] Internet-Draft PW CEP MIB October 2006 STATUS current DESCRIPTION "CEP Failure Counts (FC-CEP). The number of CEP failure events. A failure event begins when the LOPS failure is declared, and ends when the failure is cleared. A failure event that begins in one period and ends in another period is counted only in the period in which it begins." ::= { pwCepPerfIntervalEntry 23 } -- End CEP PW Performance 15 Minutes Interval Table -- CEP PW Day Performance Table pwCepPerf1DayIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF PwCepPerf1DayIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides per CEP PW performance information the current day measurement and the previous days interval. On the extreme cases where one of the error counters has overflowed during the one day interval, the error counter MUST NOT wrap around and MUST return the maximum value." ::= { pwCepObjects 7 } pwCepPerf1DayIntervalEntry OBJECT-TYPE SYNTAX PwCepPerf1DayIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created in this table by the agent for every entry in the pwCepTable and for each day interval up to the number of supported historical intervals." INDEX { pwIndex, pwCepPerf1DayIntervalNumber } ::= { pwCepPerf1DayIntervalTable 1 } PwCepPerf1DayIntervalEntry ::= SEQUENCE { pwCepPerf1DayIntervalNumber Unsigned32, pwCepPerf1DayIntervalValidData TruthValue, pwCepPerf1DayIntervalMoniSecs HCPerfTimeElapsed, pwCepPerf1DayIntervalDbaInPacketsHC Counter64, pwCepPerf1DayIntervalDbaOutPacketsHC Counter64, Zelig, et al. Expires April 25, 2007 [Page 45] Internet-Draft PW CEP MIB October 2006 pwCepPerf1DayIntervalInNegPtrAdjust Counter32, pwCepPerf1DayIntervalInPosPtrAdjust Counter32, pwCepPerf1DayIntervalInPtrAdjustSecs Counter32, pwCepPerf1DayIntervalOutNegPtrAdjust Counter32, pwCepPerf1DayIntervalOutPosPtrAdjust Counter32, pwCepPerf1DayIntervalOutPtrAdjustSecs Counter32, pwCepPerf1DayIntervalAbsPtrAdjust Integer32, pwCepPerf1DayIntervalMissingPkts Counter32, pwCepPerf1DayIntervalPktsOoseq Counter32, pwCepPerf1DayIntervalPktsOoRngDropped Counter32, pwCepPerf1DayIntervalJtrBfrUnderruns Counter32, pwCepPerf1DayIntervalPktsMalformed Counter32, pwCepPerf1DayIntervalSummaryErrors Counter32, pwCepPerf1DayIntervalESs Counter32, pwCepPerf1DayIntervalSESs Counter32, pwCepPerf1DayIntervalUASs Counter32, pwCepPerf1DayIntervalFC Counter32 } pwCepPerf1DayIntervalNumber OBJECT-TYPE SYNTAX Unsigned32(1..31) MAX-ACCESS not-accessible STATUS current DESCRIPTION "History Data Interval number. Interval 1 is the current day measuremnet period, interval 2 is the most recent previous day; interval 30 is 31 days ago. Intervals 3..31 are optional." ::= { pwCepPerf1DayIntervalEntry 1 } pwCepPerf1DayIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { pwCepPerf1DayIntervalEntry 2 } pwCepPerf1DayIntervalMoniSecs OBJECT-TYPE SYNTAX HCPerfTimeElapsed UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION Zelig, et al. Expires April 25, 2007 [Page 46] Internet-Draft PW CEP MIB October 2006 "The amount of time in the 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason or agent clock adjustments." ::= { pwCepPerf1DayIntervalEntry 3 } pwCepPerf1DayIntervalDbaInPacketsHC OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of DBA packets received." ::= { pwCepPerf1DayIntervalEntry 4 } pwCepPerf1DayIntervalDbaOutPacketsHC OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of DBA packets sent." ::= { pwCepPerf1DayIntervalEntry 5 } -- Pointer adjustment stats pwCepPerf1DayIntervalInNegPtrAdjust OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of negative pointer adjustments sent on the SONET path based on CEP pointer adjustments received." ::= { pwCepPerf1DayIntervalEntry 6 } pwCepPerf1DayIntervalInPosPtrAdjust OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of positive pointer adjustments sent on the SONET path based on CEP pointer adjustments received." ::= { pwCepPerf1DayIntervalEntry 7 } pwCepPerf1DayIntervalInPtrAdjustSecs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds in which a positive or negative pointer Zelig, et al. Expires April 25, 2007 [Page 47] Internet-Draft PW CEP MIB October 2006 adjustment was sent on the SONET path." ::= { pwCepPerf1DayIntervalEntry 8 } pwCepPerf1DayIntervalOutNegPtrAdjust OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of negative pointer adjustments seen on the SONET path and encoded onto sent CEP packets." ::= { pwCepPerf1DayIntervalEntry 9 } pwCepPerf1DayIntervalOutPosPtrAdjust OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of positive pointer adjustments seen on the SONET path and encoded onto sent CEP packets." ::= { pwCepPerf1DayIntervalEntry 10 } pwCepPerf1DayIntervalOutPtrAdjustSecs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds in which a positive or negative pointer adjustment was seen on the SONET path." ::= { pwCepPerf1DayIntervalEntry 11 } pwCepPerf1DayIntervalAbsPtrAdjust OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Absolute Pointer adjustments is relative adjustment drifts between inbound and outbound streams. It is calculated as absolute value of : ( InPosPtrAdjust - InNegPtrAdjust) - (OutPosPtrAdjust - OutNegPtrAdjust) " ::= { pwCepPerf1DayIntervalEntry 12 } pwCepPerf1DayIntervalMissingPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of missing packets (as detected via CEP header Zelig, et al. Expires April 25, 2007 [Page 48] Internet-Draft PW CEP MIB October 2006 sequence number gaps)." ::= { pwCepPerf1DayIntervalEntry 13 } pwCepPerf1DayIntervalPktsOoseq OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of sequence (via CEP header sequence numbers), but successfully re-ordered. Note: Some implementations may not support this feature (see pwCepCfgPktReorder)." ::= { pwCepPerf1DayIntervalEntry 14 } pwCepPerf1DayIntervalPktsOoRngDropped OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of range (via CEP header sequence numbers), and could not be re-ordered, or could not fit in the jitter buffer." ::= { pwCepPerf1DayIntervalEntry 15 } pwCepPerf1DayIntervalJtrBfrUnderruns OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times a packet needed to be played out and the jitter buffer was empty." ::= { pwCepPerf1DayIntervalEntry 16 } pwCepPerf1DayIntervalPktsMalformed OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected with unexpected size, or bad headers stack." ::= { pwCepPerf1DayIntervalEntry 17 } pwCepPerf1DayIntervalSummaryErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A summary of all the packet error types above (from Zelig, et al. Expires April 25, 2007 [Page 49] Internet-Draft PW CEP MIB October 2006 missing packets to bad length packets)." ::= { pwCepPerf1DayIntervalEntry 18 } pwCepPerf1DayIntervalESs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Errored Seconds encountered." ::= { pwCepPerf1DayIntervalEntry 19 } pwCepPerf1DayIntervalSESs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Severely Errored Seconds. See pwCepCfgMissingPktsToSes." ::= { pwCepPerf1DayIntervalEntry 20 } pwCepPerf1DayIntervalUASs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of UnAvailable Seconds. See pwCepCfgSesToUAS. NOTE: When first entering the UAS state, the number of SesToUas is added to this object, then as each additional UAS occurs, this object increments by one. NOTE: Similar to RFC 3592, if the agent chooses to update the various performance statistics in real time then it must be prepared to retroactively reduce the ES, SES, counts (by the value of pwCepCfgSesToUas) and increase the UAS count (by that same value) when it determines that UAS state has been entered." ::= { pwCepPerf1DayIntervalEntry 21 } pwCepPerf1DayIntervalFC OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "CEP Failure Counts (FC-CEP). The number of CEP failure events. A failure event begins when the LOPS failure Zelig, et al. Expires April 25, 2007 [Page 50] Internet-Draft PW CEP MIB October 2006 is declared, and ends when the failure is cleared." ::= { pwCepPerf1DayIntervalEntry 22 } -- End of PW CEP 1 Day Interval Performance table -- Conformance Configuration table pwCepConformanceCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF PwCepConformanceCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides the means for the agent to declare whether certain CEP PW statistics objects are supported (conformed to) or not." ::= { pwCepObjects 9 } pwCepConformanceCfgEntry OBJECT-TYPE SYNTAX PwCepConformanceCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The agent MUST create a single entry in this table." INDEX { pwCepConformanceCfgIndex } ::= { pwCepConformanceCfgTable 1 } PwCepConformanceCfgEntry ::= SEQUENCE { pwCepConformanceCfgIndex INTEGER, pwCepPerfDbaInPacketsHCTruth TruthValue, pwCepPerfDbaInPacketsHCDesc SnmpAdminString, pwCepPerfDbaOutPacketsHCTruth TruthValue, pwCepPerfDbaOutPacketsHCDesc SnmpAdminString, pwCepPerfPktsOoseqTruth TruthValue, pwCepPerfPktsOoseqDesc SnmpAdminString, pwCepPerfPktsOoRngDroppedTruth TruthValue, pwCepPerfPktsOoRngDroppedDesc SnmpAdminString, pwCepPerfSummaryErrorsTruth TruthValue, pwCepPerfSummaryErrorsDesc SnmpAdminString } Zelig, et al. Expires April 25, 2007 [Page 51] Internet-Draft PW CEP MIB October 2006 pwCepConformanceCfgIndex OBJECT-TYPE SYNTAX INTEGER (0..128) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Any arbitrary number." ::= { pwCepConformanceCfgEntry 1 } pwCepPerfDbaInPacketsHCTruth OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Tells whether the pwCepPerf...DbaInPacketsHC in the pwCepPerf...Table is supported." ::= { pwCepConformanceCfgEntry 2 } pwCepPerfDbaInPacketsHCDesc OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Explanation for pwCepPerf...DbaInPacketsHC support in the pwCepPerf...Table." ::= { pwCepConformanceCfgEntry 3 } pwCepPerfDbaOutPacketsHCTruth OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Tells whether the pwCepPerf...DbaOutPacketsHC in the pwCepPerf...Table is supported." ::= { pwCepConformanceCfgEntry 4 } pwCepPerfDbaOutPacketsHCDesc OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Explanation for pwCepPerf...DbaOutPacketsHC support in the pwCepPerf...Table." ::= { pwCepConformanceCfgEntry 5 } pwCepPerfPktsOoseqTruth OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current Zelig, et al. Expires April 25, 2007 [Page 52] Internet-Draft PW CEP MIB October 2006 DESCRIPTION "Tells whether the pwCepPerf...PktsOoseq in the pwCepPerf...Table is supported." ::= { pwCepConformanceCfgEntry 6 } pwCepPerfPktsOoseqDesc OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Explanation for pwCepPerf...PktsOoseq support in the pwCepPerf...Table." ::= { pwCepConformanceCfgEntry 7 } pwCepPerfPktsOoRngDroppedTruth OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Tells whether the pwCepPerf...PktsOoRngDropped in the pwCepPerf...Table is supported." ::= { pwCepConformanceCfgEntry 8 } pwCepPerfPktsOoRngDroppedDesc OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Explanation for pwCepPerf...PktsOoRngDropped support in the pwCepPerf...Table." ::= { pwCepConformanceCfgEntry 9 } pwCepPerfSummaryErrorsTruth OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Tells whether the pwCepPerf...SummaryError in the pwCepPerf...Table is supported." ::= { pwCepConformanceCfgEntry 10 } pwCepPerfSummaryErrorsDesc OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Explanation for pwCepPerf...SummaryError support in the pwCepPerf...Table." Zelig, et al. Expires April 25, 2007 [Page 53] Internet-Draft PW CEP MIB October 2006 ::= { pwCepConformanceCfgEntry 11 } -- End of CEP PW Conformance report table -- Conformance Information pwCepGroups OBJECT IDENTIFIER ::= { pwCepConformance 1 } pwCepCompliances OBJECT IDENTIFIER ::= { pwCepConformance 2 } -- Compliance statement for full compliant implementations pwCepModuleFullCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for agent that support full CEP PW configuration through this MIB module." MODULE -- this module MANDATORY-GROUPS { pwCepGroup, pwCepCfgGroup, pwCepPerfCurrentGroup, pwCepPerfIntervalGroup, pwCepPerf1DayIntervalGroup, pwCepConformanceCfgGroup } GROUP pwPwCepFractionalGroup DESCRIPTION "This group is only mandatory for implementations that support fractional SPE. " GROUP pwPwCepFractionalSts1Vc3Group DESCRIPTION "This group is only mandatory for implementations that support the fractional STS-1/VC-3. " GROUP pwPwCepFractionalVc4Group DESCRIPTION "This group is only mandatory for implementations that support the Fractional VC-4. " GROUP pwPwCepSignalingGroup DESCRIPTION "This group is only mandatory for implementations that support the CEP PW signaling. " Zelig, et al. Expires April 25, 2007 [Page 54] Internet-Draft PW CEP MIB October 2006 OBJECT pwCepType SYNTAX INTEGER { spe(1) } MIN-ACCESS read-only DESCRIPTION "The support of the value vt(2) or fracSpe(3) is optional. If either of these options are supported, read-write access is not required." OBJECT pwCepSonetPayloadLength MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only the default values (which are based on the pwCepType)." OBJECT pwCepCfgMinPktLength MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepCfgEnableDBA MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepCfgRtpHdrSuppress MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that do not support RTP header for CEP connections." OBJECT pwCepCfgConsecPktsInsync MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepCfgConsecMissingOutSync MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepCfgPktErrorPlayOutValue MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepCfgMissingPktsToSes MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." Zelig, et al. Expires April 25, 2007 [Page 55] Internet-Draft PW CEP MIB October 2006 OBJECT pwCepCfgSesToUas MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepCfgSecsToExitUas MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepCfgName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepCfgRowStatus SYNTAX RowStatus { active(1), notInService(2), notReady(3) } WRITE-SYNTAX RowStatus { active(1), notInService(2), createAndGo(4), destroy(6) } DESCRIPTION "Support for createAndWait is not required." OBJECT pwCepFracMode MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepFracAsync SYNTAX PwCepFracAsyncMap { other(0) } MIN-ACCESS read-only DESCRIPTION "Support for ds3(1) or e3(2) and read-write access is not required if the implementation do not support these options." OBJECT pwCepFracVtgMap MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepFracEbm MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations where the EBM is derived from configuration in other MIB modules." OBJECT pwCepFracSdhVc4Mode MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations Zelig, et al. Expires April 25, 2007 [Page 56] Internet-Draft PW CEP MIB October 2006 that support only a single pre-defined value." OBJECT pwCepFracSdhVc4Tu3Map1 MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepFracSdhVc4Tu3Map2 MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepFracSdhVc4Tu3Map3 MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepFracSdhVc4Tug2Map1 MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepFracSdhVc4Tug2Map2 MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepFracSdhVc4Tug2Map3 MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepFracSdhVc4Ebm1 MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations where the EBM is derived from configuration in other MIB modules." OBJECT pwCepFracSdhVc4Ebm2 MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations where the EBM is derived from configuration in other MIB modules." OBJECT pwCepFracSdhVc4Ebm3 MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations where the EBM is derived from configuration in Zelig, et al. Expires April 25, 2007 [Page 57] Internet-Draft PW CEP MIB October 2006 other MIB modules." OBJECT pwCepFracRowStatus SYNTAX RowStatus { active(1), notInService(2), notReady(3) } WRITE-SYNTAX RowStatus { active(1), notInService(2), createAndGo(4), destroy(6) } DESCRIPTION "Support for createAndWait is not required." ::= { pwCepCompliances 1 } -- Compliance requirement for read only compliant implementations. pwModuleReadOnlyCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for agents that provide read only support for PW CEP MIB Module. Such devices can then be monitored but cannot be configured using this MIB module." MODULE -- this module MANDATORY-GROUPS { pwCepGroup, pwCepCfgGroup, pwCepPerfCurrentGroup, pwCepPerfIntervalGroup, pwCepPerf1DayIntervalGroup, pwCepConformanceCfgGroup } GROUP pwPwCepFractionalGroup DESCRIPTION "This group is only mandatory for implementations that support fractional SPE. " GROUP pwPwCepFractionalSts1Vc3Group DESCRIPTION "This group is only mandatory for implementations that support the fractional STS-1/VC-3. " GROUP pwPwCepFractionalVc4Group DESCRIPTION "This group is only mandatory for implementations that support the Fractional VC-4. " GROUP pwPwCepSignalingGroup Zelig, et al. Expires April 25, 2007 [Page 58] Internet-Draft PW CEP MIB October 2006 DESCRIPTION "This group is only mandatory for implementations that support the CEP PW signaling. " OBJECT pwCepType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepSonetIfIndex MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepCfgIndex MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepSonetPayloadLength MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepCfgMinPktLength MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepCfgEnableDBA MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepCfgRtpHdrSuppress MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepCfgJtrBfrDepth MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepCfgConsecPktsInsync MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepCfgConsecMissingOutSync MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepCfgPktErrorPlayOutValue MIN-ACCESS read-only DESCRIPTION "Write access is not required." Zelig, et al. Expires April 25, 2007 [Page 59] Internet-Draft PW CEP MIB October 2006 OBJECT pwCepCfgMissingPktsToSes MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepCfgSesToUas MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepCfgSecsToExitUas MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepCfgRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required.." OBJECT pwCepCfgStorageType MIN-ACCESS read-only DESCRIPTION "Write access is not required.." OBJECT pwCepFracMode MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepFracAsync MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepFracVtgMap MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepFracEbm MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepFracSdhVc4Mode MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepFracSdhVc4Tu3Map1 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepFracSdhVc4Tu3Map2 MIN-ACCESS read-only DESCRIPTION "Write access is not required." Zelig, et al. Expires April 25, 2007 [Page 60] Internet-Draft PW CEP MIB October 2006 OBJECT pwCepFracSdhVc4Tu3Map3 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepFracSdhVc4Tug2Map1 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepFracSdhVc4Tug2Map2 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepFracSdhVc4Tug2Map3 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepFracSdhVc4Ebm1 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepFracSdhVc4Ebm2 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepFracSdhVc4Ebm3 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepFracRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepFracStorageType MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { pwCepCompliances 2 } -- Units of conformance. pwCepGroup OBJECT-GROUP OBJECTS { pwCepType, pwCepSonetIfIndex, pwCepSonetConfigErrorOrStatus, pwCepCfgIndex, pwCepTimeElapsed, pwCepValidIntervals, Zelig, et al. Expires April 25, 2007 [Page 61] Internet-Draft PW CEP MIB October 2006 pwCepIndications, pwCepLastEsTimeStamp } STATUS current DESCRIPTION "Collection of objects for basic CEP PW config and status." ::= { pwCepGroups 1 } pwPwCepSignalingGroup OBJECT-GROUP OBJECTS { pwCepPeerCepOption } STATUS current DESCRIPTION "Collection of objects required if the network element support CEP connections signaling." ::= { pwCepGroups 2 } pwCepCfgGroup OBJECT-GROUP OBJECTS { pwCepCfgIndexNext, pwCepConfigError, pwCepSonetPayloadLength, pwCepCfgMinPktLength, pwCepCfgPktReorder, pwCepCfgEnableDBA, pwCepCfgRtpHdrSuppress, pwCepCfgJtrBfrDepth, pwCepCfgConsecPktsInsync, pwCepCfgConsecMissingOutSync, pwCepCfgPktErrorPlayOutValue, pwCepCfgMissingPktsToSes, pwCepCfgSesToUas, pwCepCfgSecsToExitUas, pwCepCfgName, pwCepCfgRowStatus, pwCepCfgStorageType } Zelig, et al. Expires April 25, 2007 [Page 62] Internet-Draft PW CEP MIB October 2006 STATUS current DESCRIPTION "Collection of detailed objects needed to configure CEP PWs." ::= { pwCepGroups 3 } pwCepPerfCurrentGroup OBJECT-GROUP OBJECTS { pwCepPerfCurrentDbaInPacketsHC, pwCepPerfCurrentDbaOutPacketsHC, pwCepPerfCurrentInNegPtrAdjust, pwCepPerfCurrentInPosPtrAdjust, pwCepPerfCurrentInPtrAdjustSecs, pwCepPerfCurrentOutNegPtrAdjust, pwCepPerfCurrentOutPosPtrAdjust, pwCepPerfCurrentOutPtrAdjustSecs, pwCepPerfCurrentAbsPtrAdjust, pwCepPerfCurrentMissingPkts, pwCepPerfCurrentPktsOoseq, pwCepPerfCurrentPktsOoRngDropped, pwCepPerfCurrentJtrBfrUnderruns, pwCepPerfCurrentPktsMalformed, pwCepPerfCurrentSummaryErrors, pwCepPerfCurrentESs, pwCepPerfCurrentSESs, pwCepPerfCurrentUASs, pwCepPerfCurrentFC } STATUS current DESCRIPTION "Collection of statistics objects for CEP PWs." ::= { pwCepGroups 4 } pwCepPerfIntervalGroup OBJECT-GROUP OBJECTS { pwCepPerfIntervalValidData, pwCepPerfIntervalReset, pwCepPerfIntervalTimeElapsed, pwCepPerfIntervalDbaInPacketsHC, pwCepPerfIntervalDbaOutPacketsHC, pwCepPerfIntervalInNegPtrAdjust, pwCepPerfIntervalInPosPtrAdjust, Zelig, et al. Expires April 25, 2007 [Page 63] Internet-Draft PW CEP MIB October 2006 pwCepPerfIntervalInPtrAdjustSecs, pwCepPerfIntervalOutNegPtrAdjust, pwCepPerfIntervalOutPosPtrAdjust, pwCepPerfIntervalOutPtrAdjustSecs, pwCepPerfIntervalAbsPtrAdjust, pwCepPerfIntervalMissingPkts, pwCepPerfIntervalPktsOoseq, pwCepPerfIntervalPktsOoRngDropped, pwCepPerfIntervalJtrBfrUnderruns, pwCepPerfIntervalPktsMalformed, pwCepPerfIntervalSummaryErrors, pwCepPerfIntervalESs, pwCepPerfIntervalSESs, pwCepPerfIntervalUASs, pwCepPerfIntervalFC } STATUS current DESCRIPTION "Collection of statistics objects for CEP PWs." ::= { pwCepGroups 5 } pwCepPerf1DayIntervalGroup OBJECT-GROUP OBJECTS { pwCepPerf1DayIntervalValidData, pwCepPerf1DayIntervalMoniSecs, pwCepPerf1DayIntervalDbaInPacketsHC, pwCepPerf1DayIntervalDbaOutPacketsHC, pwCepPerf1DayIntervalInNegPtrAdjust, pwCepPerf1DayIntervalInPosPtrAdjust, pwCepPerf1DayIntervalInPtrAdjustSecs, pwCepPerf1DayIntervalOutNegPtrAdjust, pwCepPerf1DayIntervalOutPosPtrAdjust, pwCepPerf1DayIntervalOutPtrAdjustSecs, pwCepPerf1DayIntervalAbsPtrAdjust, pwCepPerf1DayIntervalMissingPkts, pwCepPerf1DayIntervalPktsOoseq, pwCepPerf1DayIntervalPktsOoRngDropped, pwCepPerf1DayIntervalJtrBfrUnderruns, pwCepPerf1DayIntervalPktsMalformed, pwCepPerf1DayIntervalSummaryErrors, pwCepPerf1DayIntervalESs, Zelig, et al. Expires April 25, 2007 [Page 64] Internet-Draft PW CEP MIB October 2006 pwCepPerf1DayIntervalSESs, pwCepPerf1DayIntervalUASs, pwCepPerf1DayIntervalFC } STATUS current DESCRIPTION "Collection of statistics objects for CEP PWs." ::= { pwCepGroups 6 } pwPwCepFractionalGroup OBJECT-GROUP OBJECTS { pwCepFracRowStatus, pwCepFracStorageType } STATUS current DESCRIPTION "Collection of fractional SPE objects. These objects are optional and should be supported only if fractional SPE is supported within the network element. " ::= { pwCepGroups 7 } pwPwCepFractionalSts1Vc3Group OBJECT-GROUP OBJECTS { pwCepFracMode, pwCepFracConfigError, pwCepFracAsync, pwCepFracVtgMap, pwCepFracEbm, pwCepFracPeerEbm } STATUS current DESCRIPTION "Collection of fractional STS-1/VC3 objects. These objects are optional and should be supported only if fractional STS-1/VC3 is supported within the network element. " ::= { pwCepGroups 8 } pwPwCepFractionalVc4Group OBJECT-GROUP OBJECTS { pwCepFracSdhVc4Mode, pwCepFracSdhVc4Tu3Map1, pwCepFracSdhVc4Tu3Map2, pwCepFracSdhVc4Tu3Map3, pwCepFracSdhVc4Tug2Map1, pwCepFracSdhVc4Tug2Map2, Zelig, et al. Expires April 25, 2007 [Page 65] Internet-Draft PW CEP MIB October 2006 pwCepFracSdhVc4Tug2Map3, pwCepFracSdhVc4Ebm1, pwCepFracSdhVc4Ebm2, pwCepFracSdhVc4Ebm3, pwCepFracSdhVc4PeerEbm1, pwCepFracSdhVc4PeerEbm2, pwCepFracSdhVc4PeerEbm3 } STATUS current DESCRIPTION "Collection of fractional VC4 objects. These objects are optional and should be supported only if fractional VC4 is supported within the network element. " ::= { pwCepGroups 9 } pwCepConformanceCfgGroup OBJECT-GROUP OBJECTS { pwCepPerfDbaInPacketsHCTruth, pwCepPerfDbaInPacketsHCDesc, pwCepPerfDbaOutPacketsHCTruth, pwCepPerfDbaOutPacketsHCDesc, pwCepPerfPktsOoseqTruth, pwCepPerfPktsOoseqDesc, pwCepPerfPktsOoRngDroppedTruth, pwCepPerfPktsOoRngDroppedDesc, pwCepPerfSummaryErrorsTruth, pwCepPerfSummaryErrorsDesc } STATUS current DESCRIPTION "Collection of objects declaring conformance to other objects." ::= { pwCepGroups 10 } END Zelig, et al. Expires April 25, 2007 [Page 66] Internet-Draft PW CEP MIB October 2006 8. Security Considerations It is clear that this MIB module is potentially useful for monitoring CEP PWs. This MIB can also be used for configuration of certain objects, and anything that can be configured can be incorrectly configured, with potentially disastrous results. There are number of management objects defined in this MIB module with a MAX-ACCESS clause of read-write and/or read-create. Such objects may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations. These are the tables and objects and their sensitivity/vulnerability: o the pwCepTable, pwCepCfgTable and pwCepFracTable contains objects to CEP PW parameters on a Provider Edge (PE) device. Unauthorized access to objects in these tables could result in disruption of traffic on the network. The use of stronger mechanisms such as SNMPv3 security should be considered where possible. Specifically, SNMPv3 VACM and USM MUST be used with any v3 agent which implements this MIB module. Administrators should consider whether read access to these objects should be allowed, since read access may be undesirable under certain circumstances. Some of the readable objects in this MIB module, i.e., objects with a MAX-ACCESS other than not-accessible, may be considered sensitive or vulnerable in some network environments. It is thus important to control even GET and/or NOTIFY access to these objects and possibly to even encrypt the values of these objects when sending them over the network via SNMP. These are the tables and objects and their sensitivity/vulnerability: o the pwCepTable, pwCepPerfCurrentTable, pwCepPerfIntervalTable and pwCepPerf1DayTable collectively show the CEP pseudo-wire connectivity topology and its performance characteristics. If an Administrator does not want to reveal this information, then these tables should be considered sensitive/vulnerable. SNMP versions prior to SNMPv3 did not include adequate security. Even if the network itself is secure, for example by using IPSec, even then, there is no control as to who on the secure network is allowed to access and GET/SET "read/change/create/delete" the objects in this MIB module. It is RECOMMENDED that implementers consider the security features as provided by the SNMPv3 framework "see [RFC3410], section 8", including full support for the SNMPv3 cryptographic mechanisms "for Zelig, et al. Expires April 25, 2007 [Page 67] Internet-Draft PW CEP MIB October 2006 authentication and privacy". Further, deployment of SNMP versions prior to SNMPv3 is NOT RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to enable cryptographic security. It is then a customer/operator responsibility to ensure that the SNMP entity giving access to an instance of this MIB module, is properly configured to give access to the objects only to those principals "users" that have legitimate rights to indeed GET or SET "change/create/delete" them. 9. IANA Considerations The MIB module in this document uses the following IANA-assigned OBJECT IDENTIFIER values recorded in the SMI Numbers registry: Descriptor OBJECT IDENTIFIER value ---------- ----------------------- pwCepStdMIB { transmission XXXX } Editor's Note (to be removed prior to publication): The IANA is requested to assign a value for "XXXX" under the 'transmission' subtree and to record the assignment in the SMI Numbers registry. When the assignment has been made, the RFC Editor is asked to replace "XXXX" (here and in the MIB module) with the assigned value and to remove this note. 10. References 10.1. Normative References [BCP14] Bradner, S., "Key words for use in RFCs to Indicate requirement Levels", BCP 14, RFC 2119, March 1997. [CEP] Malis, A., Pate, P., Cohen, R., Ed., and D. Zelig, "SONET/ SDH Circuit Emulation over Packet (CEP)", work-in- progress . [PWMIB] Zelig, D. and T. Nadeau, "Pseudo-Wire (PW) Management Information Base", work-in-progress . [PWTC] Nadeau, T. and D. Zelig, "Definitions for Textual Conventions and OBJECT-IDENTITIES for Pseudo-Wires Management", work-in-progress . [RFC2578] McCloghrie, K., Ed., Perkins, D., Ed., and J. Zelig, et al. Expires April 25, 2007 [Page 68] Internet-Draft PW CEP MIB October 2006 Schoenwaelder, Ed., "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999. [RFC2579] McCloghrie, K., Ed., Perkins, D., Ed., and J. Schoenwaelder, Ed., "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999. [RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999. [RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group MIB", RFC 2863, June 2000. [RFC3411] Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture for Describing Simple Network Management Protocol (SNMP) Management Frameworks", STD 62, RFC 3411, December 2002. [RFC3592] Tesink, K., "Definitions of Managed Objects for the Synchronous Optical Network/Synchronous Digital Hierarchy (SONET/SDH) Interface Type", RFC 3592, September 2003. [RFC3593] Tesink, K., "Textual Conventions for MIB Modules Using Performance History Based on 15 Minute Intervals", RFC 3593, September 2003. [RFC3705] Ray, B. and R. Abbi, "High Capacity Textual Conventions for MIB Modules Using Performance History Based on 15 Minute Intervals", RFC 3705, February 2004. [RFC3985] Bryant, S. and P. Pate, "Pseudo Wire Emulation Edge-to- Edge (PWE3) Architecture", RFC 3985, March 2005. 10.2. Informative References [RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart, "Introduction and Applicability Statements for Internet- Standard Management Framework", RFC 3410, December 2002. Zelig, et al. Expires April 25, 2007 [Page 69] Internet-Draft PW CEP MIB October 2006 Authors' Addresses David Zelig (editor) Corrigent Systems 126, Yigal Alon St. Tel Aviv, Israel Phone: +972 3 6945 273 Email: davidz@corrigent.com Ron Cohen (editor) Resolute Networks 2480 Sand Hill Road, Suite 200 Menlo Park, CA 94025 USA Email: ronc@resolutenetworks.com Thomas D. Nadeau (editor) Cisco Systems, Inc. 250 Apollo Drive Chelmsford, MA 01824 USA Email: tnadeau@cisco.com Zelig, et al. Expires April 25, 2007 [Page 70] Internet-Draft PW CEP MIB October 2006 Full Copyright Statement Copyright (C) The Internet Society (2006). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Intellectual Property The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org. Acknowledgment Funding for the RFC Editor function is provided by the IETF Administrative Support Activity (IASA). Zelig, et al. Expires April 25, 2007 [Page 71]