Network Working Group C. Yu Internet-Draft Huawei Technologies Intended status: Standards Track S. Belotti Expires: 1 September 2025 Nokia J.-F. Bouquier Vodafone F. Peruzzini TIM P. Bedard Cisco 28 February 2025 A Base YANG Data Model for Network Inventory draft-ietf-ivy-network-inventory-yang-05 Abstract This document defines a base YANG data model for network inventory. The scope of this base model is set to be application- and technology-agnostic. However, the data model is designed with appropriate provisions to ease future augmentations with application- and technology-specific details. About This Document This note is to be removed before publishing as an RFC. The latest revision of this draft can be found at https://ietf-ivy- wg.github.io/network-inventory-yang/draft-ietf-ivy-network-inventory- yang.html. Status information for this document may be found at https://datatracker.ietf.org/doc/draft-ietf-ivy-network-inventory- yang/. Source for this draft and an issue tracker can be found at https://github.com/ietf-ivy-wg/network-inventory-yang. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at https://datatracker.ietf.org/drafts/current/. Yu, et al. Expires 1 September 2025 [Page 1] Internet-Draft Network Inventory YANG February 2025 Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on 1 September 2025. Copyright Notice Copyright (c) 2025 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/ license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1. Editorial Note (To be removed by RFC Editor) . . . . . . 4 2. Terminology and Notations . . . . . . . . . . . . . . . . . . 5 2.1. Requirements Notations . . . . . . . . . . . . . . . . . 5 2.2. Terminology . . . . . . . . . . . . . . . . . . . . . . . 5 2.3. Tree Diagrams . . . . . . . . . . . . . . . . . . . . . . 8 2.4. YANG Prefixes . . . . . . . . . . . . . . . . . . . . . . 8 3. YANG Data Model for Network Inventory Overview . . . . . . . 8 3.1. Common Design for All Inventory Objects . . . . . . . . . 10 3.2. Network Element . . . . . . . . . . . . . . . . . . . . . 11 3.3. Components . . . . . . . . . . . . . . . . . . . . . . . 11 3.3.1. Hardware Components . . . . . . . . . . . . . . . . . 12 3.3.2. Software Components . . . . . . . . . . . . . . . . . 13 3.3.3. Breakout ports . . . . . . . . . . . . . . . . . . . 14 3.4. Changes Since RFC 8348 . . . . . . . . . . . . . . . . . 14 3.4.1. Component-Specific Info Design . . . . . . . . . . . 14 3.4.2. Part Number . . . . . . . . . . . . . . . . . . . . . 15 3.4.3. Component identifiers . . . . . . . . . . . . . . . . 15 4. Extending Network Inventory . . . . . . . . . . . . . . . . . 15 5. Network Inventory Tree Diagram . . . . . . . . . . . . . . . 16 6. YANG Data Model for Network Inventory . . . . . . . . . . . . 17 7. Manageability Considerations . . . . . . . . . . . . . . . . 29 8. Security Considerations . . . . . . . . . . . . . . . . . . . 29 9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 29 10. References . . . . . . . . . . . . . . . . . . . . . . . . . 29 Yu, et al. Expires 1 September 2025 [Page 2] Internet-Draft Network Inventory YANG February 2025 10.1. Normative References . . . . . . . . . . . . . . . . . . 29 10.2. Informative References . . . . . . . . . . . . . . . . . 31 Appendix A. Comparison With Openconfig-platform Data Model . . . 32 Appendix B. Terminology of Container . . . . . . . . . . . . . . 35 Appendix C. Efficiency Issue . . . . . . . . . . . . . . . . . . 35 Appendix D. Examples of ports, transceivers and port breakouts . . . . . . . . . . . . . . . . . . . . . . . . 36 Appendix E. JSON Examples . . . . . . . . . . . . . . . . . . . 36 Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . . 41 Contributors . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 42 1. Introduction This document defines a base network inventory YANG data model that is application- and technology-agnostic. The base data model can be augmented to describe application- and technology-specific information. Network inventory is a fundamental functional block in the overall network management which was specified many years ago. Network inventory management is a critical part for ensuring that the network remains healthy (e.g., auditing to identify faulty elements), well- planned (e.g., identify assets to upgrade or to decommission), and maintained appropriately to meet the performance objectives. Also, network inventory management allows operators to keep track of which devices are deployed in their networks, including relevant embedded software and hardware versions. Exposing standard interfaces to retrieve network elements capabilities as maintained in an inventory are key enablers for many applications. For example, [I-D.ietf-teas-actn-poi-applicability] identifies a gap about the lack of YANG data models that could be used at Abstraction and Control of TE Networks (ACTN) Multi-Domain Service Coordinator-Provisioning Network Controller Interface (MPI) level to report whole or partial network hardware inventory information available at domain controller level towards upper layer systems (e.g., Multi-Domain Service Coordinator (MDSC) or Operations Support Systems (OSS) layers). It is key for operators to coordinate with the industry towards the use of a standard YANG data model for Network Inventory data instead of using vendors proprietary APIs. [RFC8348] defines a YANG data model for the management of the hardware on a single server and therefore it is more applicable to the domain controller towards the network elements rather than at the northbound interface of a network controller (e.g., toward an Yu, et al. Expires 1 September 2025 [Page 3] Internet-Draft Network Inventory YANG February 2025 application or another hierarchical network controller). However, the YANG data model defined in [RFC8348] has been used as a reference for defining the YANG network inventory data model presented in this document. Network Inventory is a collection of data for network devices and their components managed by a specific management system. Per the definition of [RFC8969], the network inventory model is a network model. This document defines one YANG module "ietf-network-inventory" in Section 6. This base data model is application- and technology-agnostic (that is, valid for IP/MPLS, optical, and microwave networks as well as optical local loops, access networks, core networks, data centers, etc.) and can be augmented to include required application- and technology-specific inventory details together with specific hardware or software component's attributes. The YANG data model defined in the document is scoped to cover the common use cases for Network Inventory covering both hardware and base software information. Section 4 provides a set of considerations for future extensions of hardware, software, entitlement, and inventory topology mapping. The YANG data model defined in this document conforms to the Network Management Datastore Architecture [RFC8342]. The YANG data model defined in the document is intended to only report actual inventory data which includes both applied configuration data and state data of the network elements and components actually installed within the network. 1.1. Editorial Note (To be removed by RFC Editor) Note to the RFC Editor: This section is to be removed prior to publication. This document contains placeholder values that need to be replaced with finalized values at the time of publication. This note summarizes all of the substitutions that are needed. Please apply the following replacements: * XXXX --> the assigned RFC number for this I-D Yu, et al. Expires 1 September 2025 [Page 4] Internet-Draft Network Inventory YANG February 2025 2. Terminology and Notations 2.1. Requirements Notations The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here. 2.2. Terminology The following terms are defined in [RFC7950] and are not redefined here: * server * augment * data model * data node The following terms are defined in [RFC6241] and are not redefined here: * configuration data * state data The following terms are defined in [RFC8342] and are not redefined here: * applied configuration The following terms are defined in the description statements of the corresponding YANG identities, defined in [IANA_HW_YANG], and are not redefined here: * backplane * battery * container * cpu * chassis Yu, et al. Expires 1 September 2025 [Page 5] Internet-Draft Network Inventory YANG February 2025 * fan * module * port * power supply * sensor * stack * storage device Editors' Note: The port definition below needs to be moved to iana-hardware update Port: A component where networking traffic can be received and/or transmitted, e.g., by attaching networking cables. In case of pluggable ports, the port may be empty when no transceiver module is plugged in. TBD: Recap the concept of chassis/slot/component/board/... in [TMF_SD2-20]. Also, the document makes use of the following terms: Physical interface: An interface associated to a physical port. A physical interface is always in the lowest layer of the interface stack. Logical interface: An interface which is not associated to a physical port. Editors' Note: check whether the definitions of physical and logical interfaces can be replaced by a normative reference to [RFC8343] Editors' Note: Add recap for the concepts of chassis/slot/component/board/... in [TMF_SD2-20]. Network Inventory: A collection of data for network elements and their components managed by a specific management system. Physical Network Element: An implementation or application specific group of components (e.g., hardware components). Yu, et al. Expires 1 September 2025 [Page 6] Internet-Draft Network Inventory YANG February 2025 Network Element: The generalization of the physical network element definition. Hardware Component: The generalization of the hardware components defined in [IANA_HW_YANG] (e.g., backplane, battery, container, cpu, chassis, fan, module, port, power supply, sensor, stack, and storage device components). The list of hardware components can be extended in future versions of [IANA_ENTITY_MIB] (and, consequently, of ([IANA_HW_YANG]). Component: The generalization of the hardware component definition to include other inventory objects which can be managed, from an inventory perspective, like hardware components. Slot: A holder of the board. Board/Card: A pluggable equipment can be inserted into one or several slots (or sub-slots) and can afford a specific transmission function independently. Breakout Port: A port is usually associated with a single physical interface. A breakout port is a port which is broken down and associated into multiple physical interfaces. Those physical interfaces can have the same or different speeds and the same or different number of breakout channels. Trunk Port: A trunk port is a port which is associated with one and only physical interface. Port Breakout: The configuration of a breakout port. Note that interface channelization, when an interface (e.g., an Ethernet interface) is configured to support multiple logical sub- interfaces (e.g., VLAN interfaces), is different than port breakout and outside the scope of inventory models. Breakout channel: An abstraction of the atomic resource elements into which a breakout port can be broken down: a physical interface can be associated with one or more breakout channels but no more than one physical interface can be associated with one breakout channel. The physical elements abstracted as breakout channels are implementation specific. Appendix D provides some examples of breakout ports configurations and implementations. Container: A hardware component class that is capable of containing Yu, et al. Expires 1 September 2025 [Page 7] Internet-Draft Network Inventory YANG February 2025 one or more removable physical entities (e.g., a slot in a chassis is containing a board). Transceiver: A transceiver represents a transmitter/receiver (Tx/Rx) pair which is transmitting and receiving a signal from the media. This definition generalizes the transceiver definition in [I-D.ietf-ccamp-optical-impairment-topology-yang] to model also non optical transceivers (e.g., electrical transceivers). 2.3. Tree Diagrams The meanings of the symbols in the YANG tree diagrams are defined in [RFC8340]. 2.4. YANG Prefixes Table 1 list the prefixes of the modules that are used in this document. +========+========================+========================+ | Prefix | YANG Module | Reference | +========+========================+========================+ | inet | ietf-inet-types | Section 4 of [RFC6991] | +--------+------------------------+------------------------+ | yang | ietf-yang-types | Section 3 of [RFC6991] | +--------+------------------------+------------------------+ | ianahw | iana-hardware | [IANA_HW_YANG] | +--------+------------------------+------------------------+ | nwi | ietf-network-inventory | RFC XXXX | +--------+------------------------+------------------------+ Table 1: Prefixes and corresponding YANG modules 3. YANG Data Model for Network Inventory Overview The network element definition is generalized to support physical network elements and other types of components' groups that can be managed as physical network elements from an inventory perspective. Physical network elements are usually devices such as hosts, gateways, terminal servers, and the like, which have management agents responsible for performing the network management functions requested by the network management stations ({?RFC1157}). The data model for network elements defined in this document uses a flat list of network elements. Yu, et al. Expires 1 September 2025 [Page 8] Internet-Draft Network Inventory YANG February 2025 The "ne-type" is defined as a YANG identity to describe the type of the network element. This document defines only the "physical- network-element" identity. Other types of network elements can be defined in other documents, together with the associated YANG identity and the rationale for managing them as network elements from an inventory perspective. The component definition is also generalized to support any types of component inventory objects that can be managed as hardware components from an inventory perspective. The data model for components defined in this document uses a list of components within each network element. Different types of components can be distinguished by the class of component. The component "class" is defined as a union between the hardware class identity, defined in "iana-hardware", and the "non- hardware" identity, defined in this document. Other types of components can be defined in other documents, together with the associated YANG identity and the rationale for managing them as components from an inventory perspective. Attributes related to specific class of component can be found in the component-specific-info structure. The identity definition of additional types of "ne-type" and "non- hardware" identity of component are outside the scope of this document and could be defined in application- and technology-specific companion augmentation data models, such as [I-D.ietf-ivy-network-inventory-software]. In [RFC8348], rack, chassis, slot, sub-slot, board and port are defined as components of network elements with generic attributes. While [RFC8348] is used to manage the hardware of a single server (e.g., a network element), the Network Inventory YANG data model is used to retrieve the base network inventory information that a controller discovers from all the network elements under its control. However, the YANG data model defined in [RFC8348] has been used as a reference for defining the YANG network inventory data model. This approach can simplify the implementation of this network inventory model when the controller uses the YANG data model defined in [RFC8348] to retrieve the hardware from the network elements under its control. Yu, et al. Expires 1 September 2025 [Page 9] Internet-Draft Network Inventory YANG February 2025 +--rw network-elements +--rw network-element* [ne-id] +--rw ne-id string ... +--rw components +--rw component* [component-id] +--rw component-id string ... Figure 1: Overall Tree Structure 3.1. Common Design for All Inventory Objects For all the inventory objects, there are some common attributes Figure 2. Such as: Identifier: The UUID format is used. Such identifiers are widely implemented with systems. It is guaranteed to be globally unique. Name: A human-readable label information which could be used to present on a GUI. This name is suggested to be provided by a server. Alias: A human-readable label information which could be modified by user. It could also be present on a GUI instead of name. Description: A human-readable information which could be also input by a user. The description provides more detailed information to prompt users when performing maintenance operations. +--rw network-elements +--rw network-element* [ne-id] +--rw ne-id string +--rw ne-type? identityref +--rw uuid? yang:uuid +--rw name? string +--rw description? string +--rw alias? string ... +--rw components +--rw component* [component-id] +--rw component-id string +--rw uuid? yang:uuid +--rw name? string +--rw description? string +--rw alias? string +--rw class union ... Yu, et al. Expires 1 September 2025 [Page 10] Internet-Draft Network Inventory YANG February 2025 Figure 2: Common Attributes Between Network Elements and Components Subtree 3.2. Network Element To be consistent with the component definition, some of the attributes defined in [RFC8348] for components are reused for network elements as shown in Figure 3. +--rw network-elements +--rw network-element* [ne-id] ... +--rw hardware-rev? string +--rw software-rev? string +--rw mfg-name? string +--rw mfg-date? yang:date-and-time +--rw part-number? string +--rw serial-number? string +--rw product-name? string ... Figure 3: Network Elements Subtree Not all the attributes defined in [RFC8348] are applicable for network element. And there could also be some missing attributes which are not recognized by [RFC8348]. More extensions could be introduced in later revisions after the missing attributes are fully discussed. 3.3. Components The YANG data model for network inventory mainly follows the same approach of [RFC8348] and reports the network hardware inventory as a list of components with different types (e.g., chassis, module, and port). The component definition (Figure 4) is generalized to both hardware components and non-hardware components (e.g., software components). Yu, et al. Expires 1 September 2025 [Page 11] Internet-Draft Network Inventory YANG February 2025 +--rw components +--rw component* [component-id] +--rw component-id string +--rw uuid? yang:uuid +--rw name? string +--rw description? string +--rw alias? string +--rw class union +--rw child-component-ref +--rw parent-rel-pos? int32 +--rw parent-component-ref +--rw hardware-rev? string +--rw firmware-rev? string +--rw software-rev? string +--rw serial-num? string +--rw mfg-name? string +--rw part-number? string +--rw asset-id? string +--rw is-fru? boolean +--rw mfg-date? yang:date-and-time +--rw uri* inet:uri Figure 4: Components Subtree For state data like "admin-state", "oper-state", and so on, this document considers that they are related to device hardware management, not network inventory. Therefore, they are outside of the scope of this document. Same for the sensor-data, they should be defined in some other performance monitoring data models instead of the inventory data model. 3.3.1. Hardware Components Based on TMF classification in [TMF_SD2-20], hardware components can be divided into two groups, holder group and equipment group. The holder group contains rack, chassis, slot, sub-slot while the equipment group contains network-element, board and port. Figure 5 describes the relationship between typical inventory objects in a physical network element. Yu, et al. Expires 1 September 2025 [Page 12] Internet-Draft Network Inventory YANG February 2025 +-----------------+ | network element | +-----------------+ || || || ||1:M || || || \/ +-------------+ | chassis/ |---+ | sub-chassis |<--| +-------------+ || ______1:N______||_____1:M_______ ||------------------ ---------|| \/ \/ +--------------+ +-----------+ +---| slot | | board | |-->| /sub-slot | | | +--------------+ +-----------+ || ||1:N \/ +-----------+ | port | +-----------+ Figure 5: Relationship between typical inventory objects in physical network elements The "iana-hardware" module [IANA_HW_YANG] defines YANG identities for the hardware component types in the IANA-maintained "IANA-ENTITY-MIB" registry. Some of the definitions taken from [RFC8348] are based on the ENTITY- MIB [RFC6933]. Additional attributes of specific hardware, such as CPU, storage, port, or power supply are defined in the hardware extension. 3.3.2. Software Components This document defines "software-rev" of NEs and components, which are basic software attributes of a Network Element. Yu, et al. Expires 1 September 2025 [Page 13] Internet-Draft Network Inventory YANG February 2025 The software and hardware components share the same attributes of the component and have similar replaceable requirements. Generally, the device also has other software data, for example, one or more software patch information. The software components of other classes, such as platform software, BIOS, bootloader, and software patch information, are outside the scope of this document and defined other documents such as [I-D.ietf-ivy-network-inventory-software]. 3.3.3. Breakout ports The model defines the 'breakout-channels' presence container to indicate whether the port, which contains the transceiver module, can be configured as a breakout port or not. It is assumed that a port which supports port breakout can be configured either as a trunk port or as a breakout port. Reporting whether a port, which supports port breakout, is configured as a trunk or as a breakout port, is outside the scope of the base network inventory model. The model providing the mapping between the topology and the inventory models should provide sufficient information to identify how the port is configured and, in case of breakout configuration, which breakout channel is associated with which Link Termination Point (LTP), abstracting a device physical interface within the topology model. 3.4. Changes Since RFC 8348 This document re-defines some attributes listed in [RFC8348], based on some integration experience for network wide inventory data. 3.4.1. Component-Specific Info Design According to the management requirements from operators, some important attributes are not defined in [RFC8348]. These attributes could be component-specific and are not suitable to be defined under the component list node. Instead, they can be defined by augmenting the component-specific info container for the attributes applicable to HW e.g. boards/slot components only. Other component-specific attributes, such as SW-specific-info, may be defined in companion augmentation data models, such as [I-D.ietf-ivy-network-inventory-software] and are out of the scope of this model. Yu, et al. Expires 1 September 2025 [Page 14] Internet-Draft Network Inventory YANG February 2025 +--rw components +--rw component* [component-id] +--rw component-id string ... +--ro chassis-specific-info +--ro slot-specific-info +--ro board-specific-info +--ro port-specific-info ... 3.4.2. Part Number According to the description in [RFC8348], the attribute named "model-name" under the component, is preferred to have a customer- visible part number value. "Model-name" is not straightforward to understand and we suggest to rename it as "part-number" directly. +--ro components +--ro component* [component-id] ... +--ro part-number? string ... 3.4.3. Component identifiers There are some use cases where the name of the components are assigned and changed by the operator. In these cases, the assigned names are also not guaranteed to be always unique. In order to support these use cases, this model is not aligned with [RFC8348] in defining the component name as the key for the component list. Instead the name is defined as an optional attribute and the component-id is defined as the key for the component list (in alignment with the approach followed for the network-element list). 4. Extending Network Inventory This document defines the basic network inventory attributes applicable to typical network scenarios. For finer-grained and specific management scenarios, the relationship between this model and other models is illustrated in Figure 4. Yu, et al. Expires 1 September 2025 [Page 15] Internet-Draft Network Inventory YANG February 2025 +-------------------------+ | | | Base Network Inventory | | | +------------+------------+ | +------------------+-------------------+ | | | +------V------+ +------V------+ +------V------+ +-------------+ | | | | | | | | | Hardware | | Software | | | | Inventory | | Extensions | | Extensions | | Entitlement | | Topology | | e.g. Power | | e.g. | | | | Mapping | | supply unit | | SW patch | | | | | +-------------+ +-------------+ +-------------+ +-------------+ 5. Network Inventory Tree Diagram Figure 6 below shows the tree diagram of the YANG data model defined in module "ietf-network-inventory" (Section 6). module: ietf-network-inventory +--rw network-inventory +--rw network-elements +--rw network-element* [ne-id] +--rw ne-id string +--ro ne-type? identityref +--ro uuid? yang:uuid +--rw name? string +--rw description? string +--rw alias? string +--ro hardware-rev? string +--ro software-rev? string +--ro software-patch-rev* string +--ro mfg-name? string +--ro mfg-date? yang:date-and-time +--ro serial-number? string +--ro product-name? string +--rw components +--rw component* [component-id] +--rw component-id string +--ro class union +--ro uuid? yang:uuid +--rw name? string +--rw description? string +--rw alias? string +--ro hardware-rev? string +--ro software-rev? string Yu, et al. Expires 1 September 2025 [Page 16] Internet-Draft Network Inventory YANG February 2025 +--ro software-patch-rev* string +--ro mfg-name? string +--ro mfg-date? | yang:date-and-time +--ro serial-number? string +--ro product-name? string +--ro firmware-rev? string +--ro part-number? string +--ro asset-id? string +--ro child-component-ref +--ro parent-rel-pos? int32 +--ro parent? | -> ../../component/component-id +--ro is-fru? boolean +--ro uri* inet:uri +--ro chassis-specific-info +--ro slot-specific-info +--ro board-specific-info +--ro port-specific-info +--ro transceiver-module-specific-info +--ro breakout-channels! +--ro breakout-channel* [channel-id] +--ro channel-id uint8 Figure 6: Network inventory tree diagram 6. YANG Data Model for Network Inventory file "ietf-network-inventory@2025-02-03.yang" module ietf-network-inventory { yang-version 1.1; namespace "urn:ietf:params:xml:ns:yang:ietf-network-inventory"; prefix nwi; import iana-hardware { prefix ianahw; reference "https://www.iana.org/assignments/yang-parameters"; } import ietf-yang-types { prefix yang; reference "RFC 6991: Common YANG Data Types"; } import ietf-inet-types { prefix inet; reference "RFC 6991: Common YANG Data Types"; Yu, et al. Expires 1 September 2025 [Page 17] Internet-Draft Network Inventory YANG February 2025 } organization "IETF IVY Working Group"; contact "WG Web: WG List: Editor: Chaode Yu Editor: Sergio Belotti Editor: Jean-Francois Bouquier Editor: Fabio Peruzzini Editor: Phil Bedard "; description "This module defines a base model for retrieving network inventory. The model fully conforms to the Network Management Datastore Architecture (NMDA). Copyright (c) 2025 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Revised BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info). This version of this YANG module is part of RFC XXXX; see the RFC itself for full legal notices. The key words 'MUST', 'MUST NOT', 'REQUIRED', 'SHALL', 'SHALL NOT', 'SHOULD', 'SHOULD NOT', 'RECOMMENDED', 'NOT RECOMMENDED', 'MAY', and 'OPTIONAL' in this document are to be interpreted as described in BCP 14 (RFC 2119) (RFC 8174) when, and only when, they appear in all capitals, as shown here."; Yu, et al. Expires 1 September 2025 [Page 18] Internet-Draft Network Inventory YANG February 2025 // RFC Ed.: update the date below with the date of RFC publication // and remove this note. revision 2025-02-03 { description "Initial version"; reference "RFC XXXX: A YANG Data Model for Network Inventory."; } /* * Identities */ identity non-hardware-component-class { description "Base identity for non hardware components (e.g., software components) in a managed device."; } identity ne-type { description "Base identity for Network Element (NE) types."; } identity ne-physical { base nwi:ne-type; description "A physical network element (NE). "; } /* * Editors' Note: This identity may need to be moved to * iana-hardware update */ identity transceiver-module { base ianahw:hardware-class; description "This identity is applicable if the hardware class is some sort of self-contained sub-system which contains one or more transceivers (e.g., optical or electrical transceivers). A transceiver-module component can only be contained by a port component."; } /* Yu, et al. Expires 1 September 2025 [Page 19] Internet-Draft Network Inventory YANG February 2025 * Types */ typedef ne-ref { type leafref { path "/nwi:network-inventory/nwi:network-elements" + "/nwi:network-element/nwi:ne-id"; } description "This type is intended to be used by data models that need to reference Network Element."; } /* * Groupings */ grouping port-ref { description "This grouping is intended to be used by data models that need to reference a port component within a Network Element."; leaf ne-ref { type nwi:ne-ref; description "The reference to the Network Element which contains the port to be referenced."; } leaf port-ref { type leafref { path "/nwi:network-inventory/nwi:network-elements/" + "nwi:network-element[nwi:ne-id=current()/../nwi:ne-ref]" + "/nwi:components/nwi:component/nwi:component-id"; } must "derived-from-or-self (/nwi:network-inventory/ nwi:network-elements/nwi:network-element [nwi:ne-id=../ne-ref]/nwi:components/nwi:component [nwi:component-id=current()]/nwi:class, 'ianahw:port')"; description "The reference to the port component."; } } grouping channel-ref { description "This grouping is intended to be used by data models that need to reference one or more breakout channels within a transceivers module component."; Yu, et al. Expires 1 September 2025 [Page 20] Internet-Draft Network Inventory YANG February 2025 leaf ne-ref { type nwi:ne-ref; description "The reference to the Network Element which contains the transceiver module to be referenced."; } leaf transceiver-module-ref { type leafref { path "/nwi:network-inventory/nwi:network-elements/" + "nwi:network-element[nwi:ne-id=current()/../nwi:ne-ref]" + "/nwi:components/nwi:component/nwi:component-id"; } must "derived-from-or-self (/nwi:network-inventory/ nwi:network-elements/nwi:network-element [nwi:ne-id=../ne-ref]/nwi:components/nwi:component [nwi:component-id=current()]/nwi:class, 'nwi:transceiver-module')"; description "The reference to the transceivers module component."; } leaf-list channel-ref { type leafref { path "/nwi:network-inventory/nwi:network-elements" + "/nwi:network-element[nwi:ne-id=current()/../ne-ref]/" + "nwi:components/" + "nwi:component[nwi:component-id=" + "current()/../transceiver-module-ref]/" + "nwi:transceiver-module-specific-info/" + "nwi:breakout-channels/nwi:breakout-channel/" + "nwi:channel-id"; } description "The references to the breakout channels."; } } grouping common-entity-attributes { description "The set of attributes which are common to all the entities (e.g., component, network elements) defined in this module."; leaf uuid { type yang:uuid; config false; description "The Universally Unique Identifier of the entity (e.g., component)."; } Yu, et al. Expires 1 September 2025 [Page 21] Internet-Draft Network Inventory YANG February 2025 leaf name { type string; description "The name of the entity (e.g., component), as specified by a network manager, that provides a non-volatile 'handle' for the entity and that can be modified anytime during the entity lifetime. If no configured value exists, the server MAY set the value of this node to a locally unique value in the operational state."; } leaf description { type string; description "The textual description of the entity (e.g., component)."; } leaf alias { type string; description "The alias name of the entity (e.g., component). This alias name can be specified by network manager."; } leaf hardware-rev { type string; config false; description "The vendor-specific hardware revision string for the entity (e.g., component)."; } leaf software-rev { type string; config false; description "The vendor-specific software revision string for the entity (e.g., component)."; } leaf-list software-patch-rev { type string; config false; description "The vendor-specific patch software revision string for the entity (e.g., component)."; } leaf mfg-name { type string; config false; description Yu, et al. Expires 1 September 2025 [Page 22] Internet-Draft Network Inventory YANG February 2025 "The name of the manufacturer of this entity (e.g., component)."; } leaf mfg-date { type yang:date-and-time; config false; description "The date of manufacturing of the entity (e.g., component)."; } leaf serial-number { type string; config false; description "The vendor-specific serial number of the the entity (e.g., component) instance. It is expected that vendors assign unique serial numbers to different network element instances within the scope of the product name."; } leaf product-name { type string; config false; description "The vendor-specific and human-interpretable string describing the entity (e.g., component) type. It is expected that vendors assign unique product names to different entity (e.g., component) types within the scope of the vendor."; } } /* * Data Nodes */ container network-inventory { description "Top-level container for network inventory."; container network-elements { description "The top-level container for the list of network elements within the network."; list network-element { key "ne-id"; description "The list of network elements within the network."; leaf ne-id { type string; description "An identifier that uniquely identifies the NE in Yu, et al. Expires 1 September 2025 [Page 23] Internet-Draft Network Inventory YANG February 2025 a network."; } leaf ne-type { type identityref { base nwi:ne-type; } default "nwi:ne-physical"; config false; description "The NE type."; } uses common-entity-attributes; container components { description "The top-level container for the list of components within a network element."; list component { key "component-id"; description "The list of components within a network element."; leaf component-id { type string; description "An identifier that uniquely identifies the component in a node."; } leaf class { type union { type identityref { base ianahw:hardware-class; } type identityref { base non-hardware-component-class; } } config false; mandatory true; description "The type of the component."; } uses common-entity-attributes { refine "hardware-rev" { description "The vendor-specific hardware revision string for the component. The preferred value is the hardware revision identifier actually printed on the component itself (if present)."; reference Yu, et al. Expires 1 September 2025 [Page 24] Internet-Draft Network Inventory YANG February 2025 "RFC 6933: Entity MIB (Version 4) - entPhysicalHardwareRev"; } refine "software-rev" { reference "RFC 6933: Entity MIB (Version 4) - entPhysicalSoftwareRev"; } refine "mfg-name" { description "The name of the manufacturer of this physical component. The preferred value is the manufacturer name string actually printed on the component itself (if present). Note that comparisons between instances of the 'model-name', 'firmware-rev', 'software-rev', and 'serial-number' nodes are only meaningful amongst components with the same value of 'mfg-name'. If the manufacturer name string associated with the physical component is unknown to the server, then this node is not instantiated."; reference "RFC 6933: Entity MIB (Version 4) - entPhysicalMfgName"; } refine "mfg-date" { description "The date of manufacturing of the managed component."; reference "RFC 6933: Entity MIB (Version 4) - entPhysicalMfgDate"; } } leaf firmware-rev { type string; config false; description "The vendor-specific firmware revision string for the component."; reference "RFC 6933: Entity MIB (Version 4) - entPhysicalFirmwareRev"; } leaf part-number { Yu, et al. Expires 1 September 2025 [Page 25] Internet-Draft Network Inventory YANG February 2025 type string; config false; description "The vendor-specific part number of the component type. It is expected that vendors assign unique part numbers to different component types within the scope of the vendor."; } leaf asset-id { type string; config false; description "This node is a user-assigned asset tracking identifier for the component. A server implementation MAY map this leaf to the entPhysicalAssetID MIB object. Such an implementation needs to use some mechanism to handle the differences in size and characters allowed between this leaf and entPhysicalAssetID. The definition of such a mechanism is outside the scope of this document."; reference "RFC 6933: Entity MIB (Version 4) - entPhysicalAssetID"; } container child-component-ref { config false; description "A placeholder for adding the reference to child component(s): to further discuss whether to define a child leaf-list as RFC 8348 or a list of sub-components as openconfig-platform."; } leaf parent-rel-pos { type int32 { range "0 .. 2147483647"; } config false; description "The relative position with respect to the parent component among all the sibling components."; reference "RFC 6933: Entity MIB (Version 4) - entPhysicalParentRelPos"; } leaf parent { Yu, et al. Expires 1 September 2025 [Page 26] Internet-Draft Network Inventory YANG February 2025 type leafref { path "../../component/component-id"; require-instance false; } config false; description "The identifier of the component that physically contains this component. If this leaf is not instantiated, it indicates that this component is not contained in any other component. In the event that a physical component is contained by more than one physical component (e.g., double-wide modules), this node contains the identifier of one of these components. An implementation MUST use the same name every time this node is instantiated."; reference "RFC 6933: Entity MIB (Version 4) - entPhysicalContainedIn"; } leaf is-fru { type boolean; config false; description "This node indicates whether or not this component is considered a 'field-replaceable unit' by the vendor. If this node contains the value 'true', then this component identifies a field-replaceable unit. For all components that are permanently contained within a field-replaceable unit, the value 'false' should be returned for this node."; reference "RFC 6933: Entity MIB (Version 4) - entPhysicalIsFRU"; } leaf-list uri { type inet:uri; config false; description "This node contains identification information about the component."; reference "RFC 6933: Entity MIB (Version 4) - entPhysicalUris"; } Yu, et al. Expires 1 September 2025 [Page 27] Internet-Draft Network Inventory YANG February 2025 container chassis-specific-info { when "derived-from-or-self(../nwi:class, 'ianahw:chassis')"; config false; description "This container contains some attributes belong to chassis only."; } container slot-specific-info { when "derived-from-or-self(../nwi:class, 'ianahw:container')"; config false; description "This container contains some attributes belong to slot only."; } container board-specific-info { when "derived-from-or-self(../nwi:class, 'ianahw:module')"; config false; description "This container contains some attributes belong to board only."; } container port-specific-info { when "derived-from-or-self(../nwi:class, 'ianahw:port')"; config false; description "This container contains some attributes belong to port only."; } container transceiver-module-specific-info { when "derived-from-or-self(../nwi:class, 'nwi:transceiver-module')"; config false; description "This container contains some attributes belong to transceivers modules only."; container breakout-channels { presence "When present, it indicates that port breakout is supported."; description Yu, et al. Expires 1 September 2025 [Page 28] Internet-Draft Network Inventory YANG February 2025 "Top level container for the list of breakout channels supported by the transceivers module."; list breakout-channel { key "channel-id"; leaf channel-id { type uint8; description "An identifier that uniquely identifies the breakout channel within the transceiver module."; } description "The list of breakout channels supported by the transceivers module."; } } } } } } } } } Figure 7: Network inventory YANG module 7. Manageability Considerations 8. Security Considerations 9. IANA Considerations 10. References 10.1. Normative References [IANA_ENTITY_MIB] IANA, "IANA-ENTITY-MIB", n.d., . Yu, et al. Expires 1 September 2025 [Page 29] Internet-Draft Network Inventory YANG February 2025 [IANA_HW_YANG] IANA, "iana-hardware YANG Module", n.d., . [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . [RFC6241] Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed., and A. Bierman, Ed., "Network Configuration Protocol (NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011, . [RFC6933] Bierman, A., Romascanu, D., Quittek, J., and M. Chandramouli, "Entity MIB (Version 4)", RFC 6933, DOI 10.17487/RFC6933, May 2013, . [RFC6991] Schoenwaelder, J., Ed., "Common YANG Data Types", RFC 6991, DOI 10.17487/RFC6991, July 2013, . [RFC7950] Bjorklund, M., Ed., "The YANG 1.1 Data Modeling Language", RFC 7950, DOI 10.17487/RFC7950, August 2016, . [RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, May 2017, . [RFC8342] Bjorklund, M., Schoenwaelder, J., Shafer, P., Watsen, K., and R. Wilton, "Network Management Datastore Architecture (NMDA)", RFC 8342, DOI 10.17487/RFC8342, March 2018, . [RFC8343] Bjorklund, M., "A YANG Data Model for Interface Management", RFC 8343, DOI 10.17487/RFC8343, March 2018, . [RFC8348] Bierman, A., Bjorklund, M., Dong, J., and D. Romascanu, "A YANG Data Model for Hardware Management", RFC 8348, DOI 10.17487/RFC8348, March 2018, . Yu, et al. Expires 1 September 2025 [Page 30] Internet-Draft Network Inventory YANG February 2025 [TMF_SD2-20] TM Forum, "SD2-20_Equipment Model", TMF MTOSI 4.0, Network Resource Fulfilment (NRF), SD2-20 , May 2008, . 10.2. Informative References [I-D.ietf-ccamp-optical-impairment-topology-yang] Beller, D., Le Rouzic, E., Belotti, S., Galimberti, G., and I. Busi, "A YANG Data Model for Optical Impairment- aware Topology", Work in Progress, Internet-Draft, draft- ietf-ccamp-optical-impairment-topology-yang-17, 21 October 2024, . [I-D.ietf-ivy-network-inventory-software] Wu, B., Zhou, C., Wu, Q., and M. Boucadair, "A YANG Network Data Model of Network Inventory Software Extensions", Work in Progress, Internet-Draft, draft-ietf- ivy-network-inventory-software-00, 9 December 2024, . [I-D.ietf-teas-actn-poi-applicability] Peruzzini, F., Bouquier, J., Busi, I., King, D., and D. Ceccarelli, "Applicability of Abstraction and Control of Traffic Engineered Networks (ACTN) to Packet Optical Integration (POI)", Work in Progress, Internet-Draft, draft-ietf-teas-actn-poi-applicability-14, 25 February 2025, . [RFC7951] Lhotka, L., "JSON Encoding of Data Modeled with YANG", RFC 7951, DOI 10.17487/RFC7951, August 2016, . [RFC8340] Bjorklund, M. and L. Berger, Ed., "YANG Tree Diagrams", BCP 215, RFC 8340, DOI 10.17487/RFC8340, March 2018, . [RFC8969] Wu, Q., Ed., Boucadair, M., Ed., Lopez, D., Xie, C., and L. Geng, "A Framework for Automating Service and Network Management with YANG", RFC 8969, DOI 10.17487/RFC8969, January 2021, . Yu, et al. Expires 1 September 2025 [Page 31] Internet-Draft Network Inventory YANG February 2025 Appendix A. Comparison With Openconfig-platform Data Model Since more and more devices can be managed by domain controller through OpenConfig, to ensure that our inventory data model can cover these devices' inventory data, we have compared our inventory data model with the "openconfig-platform" model which is the data model used to manage inventory information in OpenConfig. Openconfig-platform data model is NE-level and uses a generic component concept to describe its inner devices and containers, which is similar to "ietf-hardware" model in [RFC8348]. Since we have also reused the component concept of [RFC8348] in our inventory data model, we can compare the component's attributes between "openconfig- platform" and our model directly , which is stated below: +========================+=======================+=================+ | Attributes in oc- | Attributes in our | remark | | platform | model | | +========================+=======================+=================+ | name | name | | +------------------------+-----------------------+-----------------+ | type | class | | +------------------------+-----------------------+-----------------+ | id | uuid | | +------------------------+-----------------------+-----------------+ | location | location | | +------------------------+-----------------------+-----------------+ | description | description | | +------------------------+-----------------------+-----------------+ | mfg-name | mfg-name | | +------------------------+-----------------------+-----------------+ | mfg-date | mfg-date | | +------------------------+-----------------------+-----------------+ | hardware-version | hardware-rev | | +------------------------+-----------------------+-----------------+ | firmware-version | firmware-rev | | +------------------------+-----------------------+-----------------+ | software-version | software-rev | | +------------------------+-----------------------+-----------------+ | serial-no | serial-num | | +------------------------+-----------------------+-----------------+ | part-no | part-number | | +------------------------+-----------------------+-----------------+ | clei-code | | TBD | +------------------------+-----------------------+-----------------+ | removable | is-fru | | +------------------------+-----------------------+-----------------+ | oper-status | | state data | Yu, et al. Expires 1 September 2025 [Page 32] Internet-Draft Network Inventory YANG February 2025 +------------------------+-----------------------+-----------------+ | empty | contained-child? | If there is no | | | | contained | | | | child, it is | | | | empty. | +------------------------+-----------------------+-----------------+ | parent | parent-references | | +------------------------+-----------------------+-----------------+ | redundant-role | | TBD | +------------------------+-----------------------+-----------------+ | last-switchover-reason | | state data | +------------------------+-----------------------+-----------------+ | last-switchover-time | | state data | +------------------------+-----------------------+-----------------+ | last-reboot-reason | | state data | +------------------------+-----------------------+-----------------+ | last-reboot-time | | state data | +------------------------+-----------------------+-----------------+ | switchover-ready | | state data | +------------------------+-----------------------+-----------------+ | temperature | | performance | | | | data | +------------------------+-----------------------+-----------------+ | memory | | performance | | | | data | +------------------------+-----------------------+-----------------+ | allocated-power | | TBD | +------------------------+-----------------------+-----------------+ | used-power | | TBD | +------------------------+-----------------------+-----------------+ | pcie | | alarm data | +------------------------+-----------------------+-----------------+ | properties | | TBD | +------------------------+-----------------------+-----------------+ | subcomponents | contained-child | | +------------------------+-----------------------+-----------------+ | chassis | chassis-specific-info | | +------------------------+-----------------------+-----------------+ | port | port-specific-info | | +------------------------+-----------------------+-----------------+ | power-supply | | TBD | +------------------------+-----------------------+-----------------+ | fan | | Fan is | | | | considered as a | | | | specific board. | | | | And no need to | | | | define as a | | | | single | Yu, et al. Expires 1 September 2025 [Page 33] Internet-Draft Network Inventory YANG February 2025 | | | component | +------------------------+-----------------------+-----------------+ | fabric | | TBD | +------------------------+-----------------------+-----------------+ | storage | | For Optical and | | | | IP technology, | | | | no need to | | | | manage storage | | | | on network | | | | element | +------------------------+-----------------------+-----------------+ | cpu | | For Optical and | | | | IP technology, | | | | no need to | | | | manage CPU on | | | | network element | +------------------------+-----------------------+-----------------+ | integrated-circuit | board-specific-info | | +------------------------+-----------------------+-----------------+ | backplane | | Backplane is | | | | considered as a | | | | part of board. | | | | And no need to | | | | define as a | | | | single | | | | component | +------------------------+-----------------------+-----------------+ | software-module | | TBD | +------------------------+-----------------------+-----------------+ | controller-card | | Controller card | | | | is considered | | | | as a specific | | | | functional | | | | board. And no | | | | need to define | | | | as a single | | | | component | +------------------------+-----------------------+-----------------+ Table 2: Comparison between openconfig platform and inventory data models Yu, et al. Expires 1 September 2025 [Page 34] Internet-Draft Network Inventory YANG February 2025 As it mentioned in Section 3.3 that state data and performance data are out of scope of our data model, it is same for alarm data and it should be defined in some other alarm data models separately. And for some component specific structures in "openconfig-platform", we consider some of them can be contained by our existing structure, such as fan, backplane, and controller-card, while some others do not need to be included in this network inventory model like storage and cpu. Mostly, our inventory data model can cover the attributes from OpenConfig. Appendix B. Terminology of Container Within this document , with the term "container" we consider an hardware component class capable of containing one or more removable physical entities, e.g. a slot in a chassis is containing a board. +===============================+============================+ | terminology of IVY base model | terminology in other model | +===============================+============================+ | container | holder | +-------------------------------+----------------------------+ Table 3: terminology mapping Appendix C. Efficiency Issue During the integration with OSS in some operators, some efficiency/ scalability concerns have been discovered when synchronizing network inventory data for big networks. More discussions are needed to address these concerns. Considering that relational databases are widely used by traditional OSS systems and also by some network controllers, the inventory objects are most likely to be saved in different tables. With the model defined in current draft, when doing a full synchronization, network controller needs to convert all inventory objects of each NE into component objects and combine them together into a single list, and then construct a response and send to OSS or MDSC. The OSS or MDSC needs to classify the component list and divide them into different groups, in order to save them in different tables. The combining-regrouping steps are impacting the network controller & OSS/MDSC processing, which may result in efficiency/scalability limitations in large scale networks. Yu, et al. Expires 1 September 2025 [Page 35] Internet-Draft Network Inventory YANG February 2025 An alternative YANG model structure, which defines the inventory objects directly, instead of defining generic components, has also been analyzed. However, also with this model, there still could be some scalability limitations when synchronizing full inventory resources in large scale of networks. This scalability limitation is caused by the limited transmission capabilities of HTTP protocol. We think that this scalability limitation should be solved at protocol level rather than data model level. The model proposed by this draft is designed to be as generic as possible so to cover future special types of inventory objects that could be used in other technologies, that have not been identified yet. If the inventory objects were to be defined directly with fixed hierarchical relationships in YANG model, this new type of inventory objects needs to be manually defined, which is not a backward compatible change and therefore is not an acceptable approach for implementation. With a generic model, it is only needed to augment a new component class and extend some specific attributes for this new inventory component class, which is more flexible. We consider that this generic data model, enabling a flexible and backward compatible approach for other technologies, represents the main scope of this draft. Solution description to efficiency/scalability limitations mentioned above is considered as out-of-scope. Appendix D. Examples of ports, transceivers and port breakouts Editors' Note: Need to provide some examples based on IETF 121 Slides (https://datatracker.ietf.org/doc/slides-120-ivy-2-a-yang- data-model-for-network-inventory/), and in particular: - slide 8 (100G-LR single-channel port) - slide 9 (400G-LR4 multi-channel WDM port) - slide 10 (400G-DR4 MPO port) Describe the concept of host and line channels and the mapping to breakout channels Appendix E. JSON Examples This appendix contains an example of an instance data tree in JSON encoding [RFC7951]. The example instantiates the "ietf-network-inventory" model to describe a single board with seven different types of ports, transceivers and breakouts configurations: 1. An integrated port (non pluggable). This port can be of any type (e.g., optical or electrical), single-channel or multi-channel but not supporting breakouts; 2. An empty port; Yu, et al. Expires 1 September 2025 [Page 36] Internet-Draft Network Inventory YANG February 2025 3. A single channel optical pluggable port (e.g., a 100G-LR port configured as a single 100GE interface); 4. A Wavelength-Division Multiplexing (WDM) based multi-channel optical port (e.g., a 400G-LR4 port configured as a single 400GE interface) which does not support breakouts: the four WDM channels are not reported since not relevant from inventory management perspective; 5. A Multi-Fiber Push-on (MPO) trunk-only port (e.g., 400G-DR4 port configured as a single 400GE interface). This type of MPO port does not support breakouts: the four channels are not reported since not relevant from inventory management perspective; 6. An MPO trunk port (e.g., 400G-DR4 port configured as a single 400GE interface). This type of MPO port can support either the trunk or the breakout configuration but in this example, it is configured to support the trunk configuration: the four channels are reported to support breakouts configuration, when needed. 7. An MPO breakout port (e.g., 400G-DR4 port configured as 4x100GE interfaces): the four channels are reported to support breakouts configuration. From a network inventory perspective, there is no need to distinguish between single-channel and MPO trunk-only ports. Note: as described in Section 3.3.3, reporting whether an MPO port is configured as a trunk or as a breakout port, is outside the scope of the base network inventory model. =============== NOTE: '\' line wrapping per RFC 8792 ================ { "ietf-network-inventory:network-inventory": { "network-elements": { "network-element" : [ { "ne-id": "NE-1", "description": "Network element example with ports and \ breakouts.", "components": { "component": [ { "component-id": "board-1", "class": "iana-hardware:module", "description": "Network element example with ports \ and breakouts." Yu, et al. Expires 1 September 2025 [Page 37] Internet-Draft Network Inventory YANG February 2025 }, { "component-id": "port-1", "class": "iana-hardware:port", "description": "Example of an integrated (non-\ pluggable) port.", "parent": "board-1", "parent-rel-pos": 1 }, { "component-id": "transceiver-module-1", "class": "ietf-network-inventory:transceiver-module", "description": "Example of an integrated (non-\ pluggable) port.", "parent": "port-1", "is-fru": false }, { "component-id": "port-2", "class": "iana-hardware:port", "description": "Example of an empty port.", "parent": "board-1", "parent-rel-pos": 2 }, { "component-id": "port-3", "class": "iana-hardware:port", "description": "Example of a single channel optical \ pluggable port.", "parent": "board-1", "parent-rel-pos": 3 }, { "component-id": "transceiver-module-3", "class": "ietf-network-inventory:transceiver-module", "description": "Example of a single channel optical \ pluggable port.", "parent": "port-3", "is-fru": true }, { "component-id": "port-4", "class": "iana-hardware:port", "description": "Example of a WDM multi-channel \ pluggable port.", "parent": "board-1", "parent-rel-pos": 4 }, Yu, et al. Expires 1 September 2025 [Page 38] Internet-Draft Network Inventory YANG February 2025 { "component-id": "transceiver-module-4", "class": "ietf-network-inventory:transceiver-module", "description": "Example of a WDM multi-channel \ pluggable port.", "parent": "port-4", "is-fru": true }, { "component-id": "port-5", "class": "iana-hardware:port", "description": "Example of an optical MPO pluggable \ trunk port (not supporting breakouts).", "parent": "board-1", "parent-rel-pos": 5 }, { "component-id": "transceiver-module-5", "class": "ietf-network-inventory:transceiver-module", "description": "Example of an optical MPO pluggable \ trunk port (not supporting breakouts).", "parent": "port-5", "is-fru": true }, { "component-id": "port-6", "class": "iana-hardware:port", "description": "Example of an optical MPO pluggable \ trunk port (supporting breakouts).", "parent": "board-1", "parent-rel-pos": 6 }, { "component-id": "transceiver-module-6", "class": "ietf-network-inventory:transceiver-module", "description": "Example of an optical MPO pluggable \ trunk port (supporting breakouts).", "parent": "port-6", "is-fru": true, "transceiver-module-specific-info": { "breakout-channels": { "breakout-channel": [ { "channel-id": 1 }, { "channel-id": 2 }, Yu, et al. Expires 1 September 2025 [Page 39] Internet-Draft Network Inventory YANG February 2025 { "channel-id": 3 }, { "channel-id": 4 } ] } } }, { "component-id": "port-7", "class": "iana-hardware:port", "description": "Example of an optical MPO pluggable \ breakout port.", "parent": "board-1", "parent-rel-pos": 7 }, { "component-id": "transceiver-module-7", "class": "ietf-network-inventory:transceiver-module", "description": "Example of an optical MPO pluggable \ breakout port.", "parent": "port-7", "is-fru": true, "transceiver-module-specific-info": { "breakout-channels": { "breakout-channel": [ { "channel-id": 1 }, { "channel-id": 2 }, { "channel-id": 3 }, { "channel-id": 4 } ] } } } ] } } ] Yu, et al. Expires 1 September 2025 [Page 40] Internet-Draft Network Inventory YANG February 2025 } } } Acknowledgments The authors of this document would like to thank the authors of [I-D.ietf-teas-actn-poi-applicability] for having identified the gap and requirements to trigger this work. This document was prepared using kramdown. Contributors Italo Busi Huawei Technologies Email: italo.busi@huawei.com Aihua Guo Futurewei Technologies Email: aihuaguo.ietf@gmail.com Victor Lopez Nokia Email: victor.lopez@nokia.com Bo Wu Huawei Technologies Email: lana.wubo@huawei.com Chenfang Zhang China Unicom Email: zhangcf80@chinaunicom.cn Oscar Gonzalez de Dios Telefonica Email: oscar.gonzalezdedios@telefonica.com Nigel Davis Ciena Email: ndavis@ciena.com Yu, et al. Expires 1 September 2025 [Page 41] Internet-Draft Network Inventory YANG February 2025 Authors' Addresses Chaode Yu Huawei Technologies Email: yuchaode@huawei.com Sergio Belotti Nokia Email: sergio.belotti@nokia.com Jean-Francois Bouquier Vodafone Email: jeff.bouquier@vodafone.com Fabio Peruzzini TIM Email: fabio.peruzzini@telecomitalia.it Phil Bedard Cisco Email: phbedard@cisco.com Yu, et al. Expires 1 September 2025 [Page 42]